October 21, 20178 yr I have just reinstalled my P3D which is still version 2.5 and prior to that I have unistalled PMDG product for it. After that I went to my account on PMDG and downloaded installers, but now I end up with message that it is only for v3 or v4 P3D. What to do? I don't want to spend more money as I was satisfied with what I had. But where to find installers that I originally purchased for version 2.X??
October 21, 20178 yr 2 hours ago, jasko1998 said: I have just reinstalled my P3D which is still version 2.5 and prior to that I have unistalled PMDG product for it. After that I went to my account on PMDG and downloaded installers, but now I end up with message that it is only for v3 or v4 P3D. What to do? I don't want to spend more money as I was satisfied with what I had. But where to find installers that I originally purchased for version 2.X?? This is certainly off topic. Please note PMDG forum rules require our full names on all posts. Where to find your original installers? I assume you kept them in a safe place. There is simply no reasonable way for PMDG to maintain backwards compatibility with P3Dv2.5, v3.4 or later is now required. Dan Downs KCRP
October 21, 20178 yr 2 minutes ago, downscc said: This is certainly off topic. Please note PMDG forum rules require our full names on all posts. Where to find your original installers? I assume you kept them in a safe place. There is simply no reasonable way for PMDG to maintain backwards compatibility with P3Dv2.5, v3.4 or later is now required. Thanks for help, by the way I didn't see your name on your post?
October 21, 20178 yr Just now, jasko1998 said: Thanks for help, by the way I didn't see your name on your post? Are you using a mobile device? It is there viewable in a browser. Dan Downs KCRP
November 4, 20178 yr Author One last question. When I updated from version 1C to 1D, the aircraft in all of my saved flights stopped working with lots of errors. This was a know side effect of the update. I had to go back and recreate all the flights I used for scenario training from scratch which was a lot of work. With this update will I have to again recreate all my saved flights? I am at Version 1.10.6461. Greg Clark Greg Clark
November 4, 20178 yr 57 minutes ago, greg100o said: One last question. When I updated from version 1C to 1D, the aircraft in all of my saved flights stopped working with lots of errors. This was a know side effect of the update. I had to go back and recreate all the flights I used for scenario training from scratch which was a lot of work. With this update will I have to again recreate all my saved flights? I am at Version 1.10.6461. Greg Clark Greg: You are pretty far behind, so it is possible but I think it is unlikely. In any event, you can still use your saved flights. The problem will be in the panel state so worst case is you load a scenario and have to load a new panel state. Dan Downs KCRP
January 19, 20188 yr Greg, On 11/9/2017 at 7:57 PM, greg100o said: Thanks, appreciate the support! Greg What were the exact steps you took to fix the problem of the <FOLDER_SIM2>\ error when running the install. And how did you fix the updating problem? I have the same problem. thanks Cub Meyer
January 19, 20188 yr Commercial Member 1 hour ago, meyercub said: Greg, What were the exact steps you took to fix the problem of the <FOLDER_SIM2>\ error when running the install. And how did you fix the updating problem? I have the same problem. thanks Cub Meyer Fully uninstall and the new reinstall via the new installer. Kyle Rodgers
Archived
This topic is now archived and is closed to further replies.