August 28, 20187 yr When I start the engines a caution light comes on and won't go away. Why would this happen?
August 28, 20187 yr Commercial Member 28 minutes ago, Matt Piotrowski said: When I start the engines a caution light comes on and won't go away. Why would this happen? Old panel state with a newer build. Delete your existing panel states and create new ones. Kyle Rodgers
August 28, 20187 yr Commercial Member 22 minutes ago, Matt Piotrowski said: I used the short panel state. Again - old panel state with a newer build. Please delete the state and rebuild one and it will go away. Kyle Rodgers
August 28, 20187 yr Same here. Creating a new panel state fixed it, but my spoilers are still not completely deploying after touchdown... they only go into flight detend mode.
August 28, 20187 yr Commercial Member 4 hours ago, Himbi said: Same here. Creating a new panel state fixed it, but my spoilers are still not completely deploying after touchdown... they only go into flight detend mode. This is usually more of an issue with an axis assignment or something similar. Kyle Rodgers
August 28, 20187 yr 1 hour ago, scandinavian13 said: This is usually more of an issue with an axis assignment or something similar. The spoilers are not assigned to an axle.
August 29, 20187 yr Author On 8/27/2018 at 9:16 PM, scandinavian13 said: Again - old panel state with a newer build. Please delete the state and rebuild one and it will go away. Can I use the default state to create a cold/dark state and save? Also where is the panel state folder?
August 29, 20187 yr Commercial Member 3 hours ago, Matt Piotrowski said: Can I use the default state to create a cold/dark state and save? Also where is the panel state folder? Yes this is what we recommend. Start with the default state and set the panel the way you want and save it. Location of panel state is "{SIM}\PMDG\PMDG 747 QOTS II\PanelState" Chris Makris PLEASE NOTE PMDG HAS DEPARTED AVSIM You can find us at http://forum.pmdg.com
September 4, 20187 yr On 8/29/2018 at 3:32 PM, Olympic260 said: Yes this is what we recommend. Start with the default state and set the panel the way you want and save it. Location of panel state is "{SIM}\PMDG\PMDG 747 QOTS II\PanelState" I've been getting the caution with the default cold and dark state, it goes away after all four engines are running and hydraulics are set to auto though. -Angelo Busato Angelo Busato
September 14, 20187 yr Author On 8/29/2018 at 2:32 AM, Olympic260 said: Yes this is what we recommend. Start with the default state and set the panel the way you want and save it. Location of panel state is "{SIM}\PMDG\PMDG 747 QOTS II\PanelState" So i did this like you said and everything has been fine for a couple weeks. I just installed a new livery and it came with a config file. I installed the livery with the operation center and I put the config file in {SIM}\PMDG\PMDG 747 QOTS II\AIRCRAFT. Now I get a message saying fmc message when pressing recall. Why is this happening? Should I make a new panel state form the default one again? Did I install the livery config file right?
September 14, 20187 yr 14 hours ago, Matt Piotrowski said: Now I get a message saying fmc message when pressing recall. Why is this happening? Refer to the FCOM. FMC MESSAGE literally means there is a message for you on the CDU scratchpad. Dan Downs KCRP
September 14, 20187 yr Author 1 hour ago, downscc said: Refer to the FCOM. FMC MESSAGE literally means there is a message for you on the CDU scratchpad. But there isn’t a message on the CDU scratchpad. No meessage anywhere on the fmc.
Archived
This topic is now archived and is closed to further replies.