Well, you're ahead of me. I'm not even sure what the LUA script is all about. Is that an FS script or an FSUIPC script? 

No idea, I can't get it working. I used LUA scripts in XP11, but this seems different.... 

What about using fsuipc mouse macros, used them in p3d with the honeycomb yoke

I’m lost. Totally lost. This is like programming haha.

Does anyone have any idea how to get the honeycomb alpha working with proper 1degree increments instead of 10 and trim working properly?! Without going through all of this headache....

18 minutes ago, Ianrivaldosmith said:

Does anyone have any idea how to get the honeycomb alpha working with proper 1degree increments instead of 10 and trim working properly?!

Wait for Asobo to fix their broken controller setup system. The need to go through this word not allowed again just to get controllers working is embarrassing. 

This might be of service:

https://forum.simflight.com/topic/90409-honeycomb-alpha-toggle-switch-mapping/

56 minutes ago, snglecoil said:

Wait for Asobo to fix their broken controller setup system. The need to go through this word not allowed again just to get controllers working is embarrassing. 

Without a major re-think they're still going to come up short. I had hopes that FSUIPC would not be needed this time around, but apparently that's not going to be the case. X-Plane addressed this in v11 and so should Asobo. It should support dead zones, reverser and feather control real sensitivity curves, etc. 

39 minutes ago, Agrajag said:

This might be of service:

https://forum.simflight.com/topic/90409-honeycomb-alpha-toggle-switch-mapping/

+What a mess, eh?

1 hour ago, Agrajag said:

Without a major re-think they're still going to come up short.

Time to throw the thinking caps on then. I’ll cut the team some slack for not knowing the intricacies of flight modeling and sophisticated avionics. But you just can’t mess up controller configuration. And it’s not like the Honeycomb is some fly-by-night company doing one-off custom Arduino controllers.

On 9/5/2020 at 8:07 PM, Ianrivaldosmith said:

I have managed to set it all up in FSUIPC now, I just cant get the extended lua script to work for the buttons passed 33+ 

There is a detailed explanation with the necessary Lua script on the FSUIPC forum. The sim must be running for the Lua script to work. 

https://forum.simflight.com/topic/90277-input-from-buttons-32-127-not-recognized/?tab=comments#comment-546980

Edited September 8, 20205 yr by Steku

21 minutes ago, Steku said:

There is a detailed explanation with the necessary Lua script on the FSUIPC forum. The sim must be running for the Lua script to work. 

https://forum.simflight.com/topic/90277-input-from-buttons-32-127-not-recognized/?tab=comments#comment-546980

Yup, tried all of that. Couldn’t find a command for battery. Couldn’t get the extra buttons passed 32 working. It was far too much hard work for what it really should be..... 

On 9/2/2020 at 6:24 PM, RALF9636 said:

Strange, I didn't have the issue anymore in the C152. 

Sure, nothing against FSUIPC. Glad we can finally use it.

I observed that the first time you boot the heading and altitude move as they should for a couple of seconds, then return to their crooked behavior. Maybe that’s what you experienced?

On 9/6/2020 at 4:07 AM, Ianrivaldosmith said:

I have managed to set it all up in FSUIPC now, I just cant get the extended lua script to work for the buttons passed 33+ 

Surprised to see the issue has gone for me now, only thing that changed was fsuipc and Linda are now running to power my vrinsight mcp2 hardware, I have had a few flights since and works perfectly again ?

2 hours ago, shadow133 said:

I observed that the first time you boot the heading and altitude move as they should for a couple of seconds, then return to their crooked behavior. Maybe that’s what you experienced?

Probably.

I have these buttons assigned via Linda now, and the issue is solved this way.

Is FSUIPC still required for full use of the Alpha and no heading bug?