December 9, 20205 yr Hi all, I found that when I taxi in KDEN the aircraft would suddenly tilt. It seemed that the aircraft would sink down at some points in the ground. The aircraft I used was PMDG 747-8F. Taxi route was from Gate A37 to RWY25. Then in runway 25 It happened again and could not take off. It Also happened in some taxi ways near RWY25. I did not test all runways and taxi ways but I think this could happen randomly at anywhere in Flightbeam KDEN. I have reinstalled KDEN but it didn't work. The p3d version I used was v5.1 HF1.
December 9, 20205 yr Check this thread and see if it helps: https://www.flightbeam.net/forums/viewtopic.php?f=21&t=3923 Alan
December 9, 20205 yr Author 4 minutes ago, exeodus said: Check this thread and see if it helps: https://www.flightbeam.net/forums/viewtopic.php?f=21&t=3923 Yes, I also post my problem in this thread. But I am not sure if it is mesh problem. Edited December 9, 20205 yr by Frank STY
December 9, 20205 yr Do you use orbx Central rocky mountains region? I feel like I’ve had to disable the KDEN files in that for the flightbeam airport to work properly. Dave Current System (Running at 4k): ASUS ROG STRIX X670E-F, Ryzen 7800X3D, RTX 5090, 55" Samsung Q80T, 64GB DDR5 6000 RAM, EVGA CLC 280mm AIO Cooler, Brunner CLS-E NG Yoke, Thrustmaster Warthog HOTAS & Stick, Thrustmaster TCA Quadrant & Add-on, VirtualFly Ruddo+, TQ6+ and Yoko+, GoFlight MCP-PRO and EFIS, Skalarki FCU and MCDU
December 9, 20205 yr 44 minutes ago, regis9 said: Do you use orbx Central rocky mountains region? I feel like I’ve had to disable the KDEN files in that for the flightbeam airport to work properly. I don't think CRM has anything to do with this...Orbx CRM's coverage area doesn't come anywhere close to KDEN. I just checked, and there are no KDEN files in the CRM scenery folder. This issue looks to be a result of the airport elevation being raised 0.915m in the P3Dv5 default KDEN airport scenery and/or mesh from what it was in v4. In the thread referenced above on Flightbeam's site, there's a revised ADE file created by another user that corrects the base elevation to match the default airport and mesh so there are no invisible bumps from the underlying terrain protruding above the pavements. Bob Scott | President and CEO, AVSIM Inc ATP Gulfstream II-III-IV-V Sys1 (MSFS20+24/XPlane12+11): AMD 9800X3D, water 2x240mm, MSI MPG X670E Carbon, 64GB GSkill 6000/30, nVidia RTX4090FE Alienware AW3821DW 38" 21:9 GSync, 2x4TB Crucial T705 PCIe5 + 2x2TB Samsung 990 SSD, EVGA 1000P2 PSU, 12.9" iPad Pro Thrustmaster TCA Boeing Yoke, TCA Airbus Sidestick, Twin TCA Airbus Throttle quads, PFC Cirrus Pedals, Coolermaster HAF932 case Sys2 (P3Dv5/v4): i9-13900KS, water 2x360mm, ASUS Z790 Hero, 32GB GSkill 7800MHz CAS36, ASUS RTX4090 Samsung 55" JS8500 4K TV@60Hz, 3x 2TB WD SN850X 1x 4TB Crucial P3 M.2 NVME SSD, EVGA 1600T2 PSU Fiber link to Yamaha RX-V467 Home Theater Receiver, Polk/Klipsch 6" bookshelf speakers, Polk 12" subwoofer, 12.9" iPad Pro PFC yoke/throttle quad/pedals with custom Hall sensor retrofit, Thermaltake View 71 case, Stream Deck XL button box Sys3 (DCS/P3Dv4/ATS/ETS): AMD 7800X3D, MSI MPG X870E Carbon, Noctua NH-D15S, 64GB GSkill 6000/30, EVGA RTX3090 Alienware AW3420DW 34" 21:9 GSync, Corsair HX1000i PSU, 4TB Crucial T705 PCIe5 + 2TB Samsung 970Evo Plus, TM TCA Officer Pack, Saitek combat pedals, TM Warthog, TM RS300 FF wheel/pedals, Coolermaster HAF XB case
December 9, 20205 yr Ahh my mistake. Dave Current System (Running at 4k): ASUS ROG STRIX X670E-F, Ryzen 7800X3D, RTX 5090, 55" Samsung Q80T, 64GB DDR5 6000 RAM, EVGA CLC 280mm AIO Cooler, Brunner CLS-E NG Yoke, Thrustmaster Warthog HOTAS & Stick, Thrustmaster TCA Quadrant & Add-on, VirtualFly Ruddo+, TQ6+ and Yoko+, GoFlight MCP-PRO and EFIS, Skalarki FCU and MCDU
December 9, 20205 yr Checkout Aerosoft EDDF for v5 it uses sloped runways and all taxiways have a height elevation on the nodes, slew over the hard standing on the west and you will drop down a hole in some places. Raymond Fry.
December 10, 20205 yr Author Hi all, Problem solved. It is caused by an elevation problem of Flightbeam KDEN. And I have fixed it. You can check the Flightbeam forum for detail. http://flightbeam.net/forums/viewtopic.php?f=21&t=3737#p21410
December 10, 20205 yr Although the .zip file does work to fix the sunken taxi signs and the other issues like mentioned in the OP, it also makes the entire airport dead flat. There are supposed to be some minor elevation changes around the airport that are no longer there. So, it's half fixed (but usable) for now. i9-10850K, ASUS TUF GAMING Z490-PLUS (WI-FI), 32GB G.SKILL DDR4-3603 / PC4-28800, GIGABYTE RTX5080 16GB WF OC 3 FAN running 3440x1440
Archived
This topic is now archived and is closed to further replies.