bruskey

I have had mine for at least a couple years now and have not had any major issues. It's not metal mind you but wood and I use it for both P3D and MSFS 2020. The only thing I had to do is tighten the throttles and gear down lever so they don't fall down on their on, this is a little tricky to get to the screws underneath but doable. I found the throttles are a good option and I have the under desk mount which positions the unit pretty well. Yes I would have liked metal and hall sensors but for me this worked with my budget. Bruce

Hello. When using Pilot2Atc in msfs I don't get a response from controllers until after several attempts or I have to revert to using sayit interface to get a response. In P3D I do not have this issue, I always get a response on first attempt. This is for many requests like clearance, pushback, taxi, etc. So it's not one phrase. I tried retraining voice recognition turning up mic volume, etc. Anyone else come across same where you can offer some advice? Thanks Bruce

Yes I tried just Connecting, several attempts, to no avail, only complete shutdown and restart helped and as I mentioned this even took a couple attempts before finally connecting. Thanks for log location next time I encounter this issue will see what logs might say and pass along same. Bruce

Hello. I have the latest FSUIPC 7 Beta installed and in order for Pilot2ATC to connect to MSFS 2020 i have to stop it and start it 2 or 3 times, I'm following the directions to be Ready to Fly, FSUIPC started, and running as Admin. Is there a log file that i could look at that might suggest why it does not want to connect on the 1st or 2nd and even sometimes 3rd attempt? Once it connects it works fine. Thanks, Bruce

I have restored back to originals as well every version of envshade I have tried on v5 gives me psychedelic cloud colored textures once in a while. Even seeing this on ground textures as well. Does not happen all the time but enough to kill the immersion. I need to post this on their site to see if anyone else is seeing same. And yes I have cleared shaders. Bruce

Are you all seeing some pixelation or blockiness to the truesky clouds even at ultra settings, not seeing much difference from medium, high to ultra setting. Worse when approaching the cloud at same altitude, they do appear less blocky when looking down on top of them though.

Hello, I updated to 2.5.0.3 and now the responsiveness of the application has slowed way down. In 2.5.0.2 import a flight plan maybe 5 to 10 seconds, in 2.5.0.3 at least a minute or i get a "not responding" message in the import window at top. Also, other areas like searching for way point or sid or star takes much longer and i also get a "not responding" message until it finally loads. I did install latest navigraph update. Anyone seen this issue? Thanks, Bruce

Has happened to me twice over the last 6 flights with the Hawker, something is turning the fuel (HP Cocks) off without reason to my knowledge. I'm still looking for root cause as well. Bruce

Hello, really enjoyed the trial version and decided to purchase, still learning, however, really increased the immersion factor for me. Is there a preferred way to ask for a deviation around weather while en-route? Is this even an option? Thanks, Bruce Looks like i posted this in the bug forum instead of the users forum,sorry

I noticed that the over speed indicator on the Hawker MFD does not show/indicate properly where the standby horizon does. At flight levels the standby horizon over speed starts to go off right at the mach .80 whereas the MFD still shows room, as much as 30 to 40 knots, before seeing the red line over speed indicator appear. Was curious if others are experiencing same thing. Thanks Bruce

I had significant vsync issues with the 388.00 driver and my 1080TI, I went back to 387.92. Not sure if I'm going to try 388.13 or not.

I have applied V2 mod as well and like you the altitude and vs knobs do not work in VC, however, the knobs light up and you can turn them etc. Interestingly, I can use my VRinsight panel to adjust ALT and VS so I do have a work around. Bruce

I don't know if it is just my 6700K but I also see that P3D uses core 0 at almost 100% after starting up. To resolve this, I go into task manager and set P3D to use just cores 2 and 3 for about 5 or 10 seconds and switch back to all cores and from there on out all my CPU cores are well balanced, no more hogging of core 0. Bruce

Hi, if you have the Descent Briefing turned on under the sound options try turning that off, I had similar random TOD crashes and this fixed it for me. Bruce

Hello, does anyone know why with HDR on under P3D the landing lights on the 737NGX look just fine from both VC and outside, however, with HDR off the landing lights look low resolution or "washed out". I prefer to fly without HDR on but the lights look so much more realistic with it on. Bruce