Butch1

Looking for a P3DV5 compatible de Havilland Canada DHC-4 Caribou. Thanks

I don't see anything in the views menu bar that opts for ground support equipment. I did manage to add the P8 to my addons folder and createan add xml file. Thanks anyway. I don't see any switches in the cockpit that would activate any GSE either. I wish there was a way to create a clean look. (No pylons or armament.)

There is a sound folder that will announce landing approach info i.e. approaching minimums, decent in feet remaining (2,500/1,000/etc. but it is for 32 bit system so I incorporated the 64bit sound system from here (DSD XML Sound 64) In the readme there is info on how to set it op for P3D4 and up. One thing I noticed in this aircraft is the notification of exceeding speed for landing gear drop.

I noticed that the model file shows in a few ground support equipment items in MCDX. I don't see them in P3DV5. How are these items activated?

I recently installed the P8 Complete Navy P8 by Chris Evans and in the preview screen the wings are clipped (gone) but later show when it loaded and on the runway ready to go. If I select a different aircraft, and it loads then go back again to select the P8, the wings are showing in the preview screen. When I close P3D (V5) and re open and select the P8l the wings are clipped again till I rinse and repeat what I stated above. I didn't mess with any of the aircraft.cfg contents either.

Thanks Ted for the bump back. I have Gmans email and he stays in touch now and then. As you may know, he lives in the Mammoth Lake area and his comms are intermittent. I am with P3DV5.3 and not interested in that MSFS2020 at all. Too much invested ($$) in P3D. I was instrumental in getting Gordon and Thomas Woods of CR1 software together. Gordon was really appreciative that I got them acquainted. So "G" is putting a lot of P3D V5 aircraft together for Thomas. Have you seen Gordons youtubes of late? He has some good ones out there. Well, please stay in touch. Nice to of got in touch with you again.

Hi Ted, Haven't seen you in ages. Are you into P3DV5 aircraft and or sceneries? Talked to Gman and stay in touch with him. Take care

Well, last time I checked,.... the Coronado bridge is included with LatinVFR San Diego (KSAN). I use to cross over it back in the early '70's to Navy fire fighting school at North Island when is was a toll bridge. I believe is is a free bridge now. Notice the San Diego skyline in the background.

+ backwards compatibility with P3D scenery. In V5, object bleed thru were common when using V4 scenery in V5. I hope they don't make the same bungle.

You may already know this, but when installing V4 scenery to V5 there will be a bleed thru of scenery objects from V5 thus buildings from V5 will show thru the V4 scenery, i.e. V4 will show a hanger that is halfway inside a V5 hanger or part of a V5 runway will not be aligned with V4. Bits and pieces of V5 objects will not jibe with V4.

I'm thinking the same, but thanks I'll post over there.

Is it possible to convert MSFS2020 scenery to P3D V5? If so, what would be the procedures? I see a lot of converting the other way but not from MS2020 to P34DV5.......

I've managed to remove ALL those people and with changes at real airport, I've relocated the A7 along side another ex gate guard (A5) and have re located them.

Thank you David for all your help. I've learned a little more about ADE from you. : C )

I've managed to move the hangers/buildings that were sitting in the middle of that gray road. It helped when ADE would load that airport and the location of the aircraft so that I could locate the buildings that needed to be relocated.

Looks like P3DV5 has got the layout right; the gray road does exist but is not depicted in P3DV4, I'm guessing that I would have to located those buildings that are sitting on that gray access road and make estimated guess on where to move them. Is there such a thing as a vector data editor for P3D5?

For some reason When I compile in ADE a gray road is added to the scenery. This road is not visible in either P3DV4 or V5 ADE outllned with red line Ade doesn't show that road, it is only seen in the sim (P3DV5). It looks like that gray road is only in P3DV5 and not V4. Reason I mention this is there are buildings that are on that road and no way I know of can I remove the road. Otherwise the import of ADE objects went well but puts some building on that gray road in P3DV5. It's invisible in ADE but not {3DV5.

I have prokey installed and that didn't change a thing. I've managed to export/import the buildings but in P3DV5 they are not positioned the same as in P3D V4 This is overhead in P3D V4 This is overhead in P3DV5 - Notice the buildings are not situated exactly as in above screen shot Some buildings are in the middle of tarmacs or roads.

Okay, I found an alternate way to export/import and now all the objects are not aligned in P3D5 as they are in P3D4 so what needs to be done so that all the buildings etc are situated in P3DV5 like they are in P3DV4?

No my version is newer then yours, hence the missing select in display option/button which was the point of my discussion. and to repeat my question, using the version I have, what is the next step after selecting the buildings? My screen grab was just for posting here and I realized that I have to filter out the objects that are NOT buildings. Again, I am using the latest and greatest version 1.79.7475 Edit: Just for grins, I found and installed the same version you use and still didn't see that select in display button.

AFAIK I have the latest version.

Thanks for the bump back, My version 1.79.7475 doesn't have that button so I wonder what to do next without that select button you have?

In ADE Can only save as csv file.

I've been trying to so this export and I too do not see a select in display either. How do I export all those files selected, i.e. the next step Thanks.