Tyler_J

I use neither AES or GSX so can't be related. Im running pretty much default. No terrain/mesh or weather add ons at the moment.

This is happening to me at default FSX airports. Havent flown to any addons lately but I'll find out in a bit. Also I believe my mesh is on 1M. Can anyone confirm this happening on other settings?

Hey guys, So after the upgrade to SP1C I have noticed the plane (-700 and -900 is all I've used since the update) seems to bounce around the runways and taxiways. It happens regardless of the aircrafts load, whether I have just loaded in or just landed. Any ideas guys? At first I ignored it but now its getting rather annoying. - Tyler

Perhaps as a cabin trainer? Or for Emergency Services to train with? I doubt the latter though as surely there would have been frames closer to home to use.

Hi guysJust curious if Southwest has received any of their planned upgrades to the 737-300 fleet? I read a while ago on Flight Global that delivery was to start early 2011. Is the project still active?See the article below...www.flightglobal.com/news/articles/picture-southwest-launches-737-300-cockpit-upgrade-with-boeing-and-ge-320450/

I'll have to give that one a check for myself tomorrow. Good find!On a side note, what does 'Gear Off' actually do? I assume it just disconnects power to the landing gear?

It could very well be an outdated AIRAC cycle? Are you still using the default 1108? Otherwise it could be an old route? If RouteFinder has given you an old route it could have listed an old STAR - I can't be sure as I use vRoute.

Ahhh that makes sense. Thank you for your help.

I have not experienced this on the NGX however I had a similar problem with the MD-11. When it loaded in gauges would be blacked out, switches would be out of place, flaps down and the gear would be spun around. It turned out I had inadvertantly switched planes in FSX before the 20 second countdown had completed, and somehow that had messed with the load in.I found a reinstall did the trick, however by the 4th time this had happened I had isolated which particular file had been causing the issue and simply made a copy, for whenever it happened again.

I have a similar system to the OP:2600K at 4.7Gigabyte Z68A16GB 1600Mgz RAMGTX 580 ('Super' Overclocked)Coolermaster V8On my modest 22" screen I see a very nice increase in visual quality, but I also see a frame drop of around 5-10 when on the ground. I am yet to run a few flights to see how this performs over the whole flight but at the moment it seems to work well.I will note however that frames are much more stable - I see 36-45 in thunderstorms, on the ground, in the VC at defaul JFK (my test airports for tweaks are JFK, LHR and LAX - frames at these airports make my final decision on tweaks haha). Before this it was a little higher, but more jumpy. Nice work bakaman!

Hey guys,Long time reader - first time poster. I have found this forum to be a wealth of knowledge.I have a little question regarding the MCP, specifically the LED indicating the selected speed. Sometimes when dialing in a lower speed I see a flashing 'A' in front of my speed. I have ran through the manuals, but can't seem to find reference to it. I don't doubt that it is in the manuals however I am having trouble searching as I have no clue how to describe it other than as I have done above. I assume it is a warning that I have dialed in a speed below stall speed, or that is risking a stall, however am not sure.Any insight would be appreciated.Apologies if this has been discussed or is obvious however I'm a little curious by this.Keep them flying high.Tyler Cardy

For me its not quite 'there' yet. Its scenery looks amazing but the graphic models of aircraft arent really to my liking. However I must admit I have not yet flown X-Plane 10 yet - just been looking at the pictures If X-Plane 10 was to grow into a stable base sim with lots of great developer support though I could certainly see myself making the move in the future.