Pitter

Ok, we closed it up here. It´s not a big problem. Thanks for your help. Have a nice evening. Peter

Yes, I have red the manual, but that was 1 week after very first release of RC. AI package is UTL, Thanks, Peter

Hi Ray, yes, I did that already. Those word not allowed chatter files are gone, but all other also. I hear now, lets say, only those planes which also approach the same airport, as mey. Is very quiet in the air. But if that is the only way, I can live with that, because is only in the above mentioned area. Thanks for your help Peter

Hi Ray, sorry, but I don´t know what you mean? I have only those files which included in the "regular" RC4 package. You hear those only, if you are flying around Japan, Australia and New Zealand. For the real world: those are mainly used for position reports during Trans Atlantic/Pacific crossing, before Datalink was available. Peter

Is there a simple way to remove or deaktivate the HF chatter files? Thanks, Peter

I brought the Carenado Phenom300 around 2 weeks ago, and before yesterday I de-installed them fromP3D. Since then I have a strange problem with my remaining A/C, AS Bus, (318-321) and Lvl-D. I can only open the left front entry door. If I try another one, like rear pax door or any cargo door, the fwd entry closed. So, whichever door i try to open, only fwd left entry opens and closed. Do I have manually de-install any leftovers? Any help are welcome Peter

I brought the Carenado Phenom300 around 2 weeks ago, and before yesterday I de-installed them fromP3D. Since then I have a strange problem with my remaining A/C, AS Bus, (318-321) and Lvl-D. I can only open the left front entry door. If I try another one, like rear pax door ord caorgo door, the fwd entry closed. So, whichever door i try to open, only fwd left entry opens and closed. Any help are welcome. Peter

Ignore my threat. fault 2 is spread now over all my planes, not only Carenado. Will going with a back-up. Peter

Hi all, I have again problems with the Phenom 300. 1.) I'm unable to select fuel weight in KG at the AUX page. Only selectable are IG and LBS, but the cursor cannot be set to KG 2.) I cannot open the baggage door fwd and/or aft. It does'nt matter I use the control panel or the std key strokes. If, for example the entry door is open and I select fwd or aft baggage, the entry door closed. If all doors are closed, and I select the fwd/aft door, the entry door opens. Any help welcome Peter

Hi Bill,. that was the trick. I already had controls disabled in p3d, but within controls\others\enable force feedback I disabled now "Control surfaces" and "retractable landing gear" and now it works like it should be. I do not understand that, but...…... Thanks, Peter

Because I have all my controls in all my planes assigned via FSUIPC, and all of them working without any problem. So, there should be a reason why it is not happen with Carenado's gear and flaps. And that I try to find out and fix it Thanks, Peter

Hi all, I'm new to the Phenom and have so far two problems in P3Dv3.4. I have all my flight controls, throttle, gear and flaps assigned via FSUIPC. Every plane I have is working very well, except the Phenom: Flaps and gear operated only with the default key(board) press, in both direction. Rudder, Elevator as well as Aileron and Throttle working via FSUIPC assignment. Any help is very appreciated. Peter

In FSX I could view around with mouse wheel holding pushed and moved the mouse. This works inside and outside. I do not have that within v3.4 Do I need to setup something? Peter

problem solved with fresh install without HiFi Tks for your help Peter

Shaders already exchanged, no help. Anyway, thanks for your tip Peter

I´m new to P3Dv3.4 (no money for another PC) So most of my stuff from FSX works very well. I also installed HIFI ActiveSky for P3Dv3. Since them I lost all my airplane lights , beacon, strobe, nav, ldg, Then I de-installed Active Sky and bingo. Lights are back. I noted that during de-install AS says "replace your shaders" or something like that. So how can I have my lights and AS? Peter

ifly.com is usefull Peter

Good advice Charlie with this gauges recovery tool, but sadly no luck at all. Startet recover with FSX, then SP1 and finally also Sp2. Did not work. So, I checked the effects folder for another set of those lights. For testing I renamed the "fx" files at the FSX King AIr with the beacon and strobes from ESDG, and both are working. So far I can live with that, just rename the light entries. Tks for your help. Peter

Sorry not making it clear. All aircraft which using FSX own nav, beacon, and strobe lights, regardless if a switch is using or "L" key. Effect files are inside effect folder and the "light" section inside aircraft.cfg looks ok. Peter

Hi all, the title say´s it all. All the relevant fx files are inside the effects folder. Anyone have any idea while the lights are failing?? Peter

Is that a joke, or how to understand tat price tag?? 119.95$ not bad at all Peter

I also received this mail. I do not need charts from Navigraph. Mine coming free of charge from the net. If they change the pricing to this new level, I will be a new customer with Aerosoft. Peter

Thanks a lot Ray. Peter

Hi Ray, getting FSUIPC from the link you given, and install (overwrite existing FSUIPC). A warning was popping up, says something about simconnect, which I did not understand, but offered me a fix. So I let him fixed, started fsx and voila, you again the man of the year. All working fine. Another 2 question: I had to install a valid copy of the fsx.exe file, placed inside the P3D Folder. Can I remove that file or does it not harm anything? The 2nd one has noting to do with RC, but maybe now now a trick: whenever I open a menue inside running P3D the sim goes by by himself into "paused mode". Is there a workaround to removed that auto paused mode??? Anyway, thank you very much for your quick help Peter

Hi Ray, the latest for FSX/P3Dv3 4 4.971 Peter