Jump to content

Archived

This topic is now archived and is closed to further replies.

Stelios

Service Pack 1C

Recommended Posts

Hi guys

 

Long time unsent from these columns due to sickness but I am back.

 

Now I have installed the Service Pack 1C for my PMDG 777 and I have noticed that the operation of the FMC has changed a bit.

Is there a write up somewhere or a video of how the FMC should work now after the Service Pack 1C?

 

Also I have noticed that before the service pack, when the autopilot was disengaged you could silence the buzzer sound by pressing  CTRL SHIFT Z  Now since the service Pack this doesn't work.

 

Thanks

Stelios 


Stelios Christofides

Share this post


Link to post
Share on other sites

 

 


Also I have noticed that before the service pack, when the autopilot was disengaged you could silence the buzzer sound by pressing CTRL SHIFT Z Now since the service Pack this doesn't work.

 

Many months of testing and I did not know that... always right clicked the screw twice about 1.5 s or more apart.

 

Note the Introduction  document was updated for changes in SP1.. you'll find a lot of information there so it is a good place to start.

 

Stay healthy!


Dan Downs KCRP

Share this post


Link to post
Share on other sites

 

 


Is there a write up somewhere or a video of how the FMC should work now after the Service Pack 1C?

 

It was the service pack in general that changed that. SP1b and SP1c don't have any radical changes to the FMC. The changes are noted in the intro manual, where one would expect a digest of information like that.

 

 

 


Also I have noticed that before the service pack, when the autopilot was disengaged you could silence the buzzer sound by pressing  CTRL SHIFT Z  Now since the service Pack this doesn't work.

 

My guess is that you just need to go back into your key commands and set the command for AP DISCONNECT again.


Kyle Rodgers

Share this post


Link to post
Share on other sites

I have checked on the PMDG site and I could not find the intro manual. for the SP1C. Can someone post the link please?

stelios


Stelios Christofides

Share this post


Link to post
Share on other sites

In the start menu I have 2 documents 1. PMDG 777 Introduction and 2. PMDG 777 Tutorial 1

Nothing on the SP1C

 

stelios


Stelios Christofides

Share this post


Link to post
Share on other sites

You might try checking the PMDG Operations Center. Even after I installed SP1c, there were still updates there for the -200 and -300.


Stuart Ball

 

Share this post


Link to post
Share on other sites

so now? No notes on the SP1C?

 

Strange on my start menu I have  the sp1  c on the introduction manual

 

Aj4Wc.png


I7-800k,Corsair h1101 cooler ,Asus Strix Gaming Intel Z370 S11 motherboard, Corsair 32gb ramDD4,    2  ssd 500gb 970 drive, gtx 1080ti Card,  RM850 power supply

 

Peter kelberg

Share this post


Link to post
Share on other sites

Yep, the intro doc has been updated by SP1c, but still no SP1c changelog is mentioned (except for Robert's topic in this forum).

 

True but in my introduction manual the changes are hightlighted in green saying  the changes  that were made( in green it  says new to sp1  after  any paragraph   that have changes  to it)


I7-800k,Corsair h1101 cooler ,Asus Strix Gaming Intel Z370 S11 motherboard, Corsair 32gb ramDD4,    2  ssd 500gb 970 drive, gtx 1080ti Card,  RM850 power supply

 

Peter kelberg

Share this post


Link to post
Share on other sites

So why then PMDG does not have a link in their site for people to read it? Anyone from PMDG here?

 

stelios


Stelios Christofides

Share this post


Link to post
Share on other sites

Because the documentation (introduction manual)  can be found in 3  places on your pc,   operation centre,  your start menu  and  your fsx/pmdg777  on where you got your t7  installed on your drive under documentation


I7-800k,Corsair h1101 cooler ,Asus Strix Gaming Intel Z370 S11 motherboard, Corsair 32gb ramDD4,    2  ssd 500gb 970 drive, gtx 1080ti Card,  RM850 power supply

 

Peter kelberg

Share this post


Link to post
Share on other sites

Guys I found it in the in the fsx/pmdg777 documentation. Thanks a lot for your input and sorry for all your troubles.

 

stelios


Stelios Christofides

Share this post


Link to post
Share on other sites

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    34%
    $8,535.00 of $25,000.00 Donate Now
×
×
  • Create New...