September 7, 201510 yr Ok was looking for some possible help. After being visited by our unwanted friend, I wanted to see if I am doing something wrong. I have ensured that I have all of the latest updates and that I am running the latest software. Ok we go I continue to get plagues on the following flight. YSSY (Fly Tampa settings to minimal) to KSFO (Flighthbeam). I am using ASNext with Textures from REX. Only have California Central and Northern Photo scenery activated. All other Airports and Photo scenery are inactivated. I have the FO screens shut off. My system settings are as follows: Textures: 1024 LOD: 4.0 Autogen: None Water: Mid 2x AI Cars, Boats, Ships: 0 UT2 AI Commercial: 60 UT2 AI Private: 0 After I depart YSSY my VAS stays steady at approx 2.8-2.9, however as the day progresses into night the VAS slowly climbs and hits the 4.0 mark. This seems to be common only to this area, I can fly KSFO-EGLL with essentially the same settings, only difference is that when I depart in the night I don't run into the same problem and can make it to EGLL. If you require any further information, please let me know, other than that I am looking for any support to resolve this issue. V/R Kristopher Plummer
September 7, 201510 yr Have a look at my guild in my sig below. Hope it might help? Having said that KSFO to EGLL is doing well, loading dusk night textures is not going to help. David Murden. MSFS • Fenix A320 • PMDG 737 • MG Honda Jet • 414 / TDS 750Xi • FS-ATC Chatter • FlyingIron Spitfire & ME109G • MG Honda Jet • • Fenix A320 Walkthrough PDF • Flightsim.to • DCS • A10c II • F-16c • F/A-18c • F-14 • (Others in hanger) • Supercarrier • Terrains = • Nevada NTTR • Persian Gulf • Syria • Marianas • • [email protected] All Cores HT ON • 32GB DDR4 3200MHz • RTX 3080 • TM Warthog HOTAS • TM TPR • Corsair Virtuoso XT with Dolby Atmos® • Samsung G7 32" 1440p 240Hz • TrackIR 5 & ProClip •
September 7, 201510 yr Commercial Member I would first run the flight on a stock FSX setup with just the 777, see how that goes. Then introduce half the addons, then the other half. Divide and conquer. Steve Waite: Engineer at codelegend.com
September 7, 201510 yr I can almost guarantee it's your AI traffic. I have started to have some serious fps issues (and possibly VAS) in P3D, utilizing AI traffic. I think your AI traffic may be set a little too high. I have found having commercial traffic at around 30 would be sufficient...just a thought. -Jim Engage, research, inform and make your posts count! -Jim Morvay Origin EON-17SLX - Under the hood: Intel Core i7 7700K at 4.2GHz (Base) 4.6GHz (overclock), nVidia GeForce GTX-1080 Pascal w/8gb vram, 32gb (2x16) Crucial 2400mhz RAM, 3840 x 2160 17.3" IPS w/G-SYNC, Samsung 950 EVO 256GB PCIe m.2 SSD (Primary), Samsung 850 EVO 500gb M.2 (Sim Drive), MS Windows 10 Professional 64-Bit
September 7, 201510 yr Commercial Member Disable all AI traffic, all weather, and all scenery then try it again. Kyle Weber (Private Pilot, ASEL; Flight Test Engineer)Check out my repaints and downloads, all right here on AVSIM
Create an account or sign in to comment