FSL A320X v2.0.1.258

[FS++ 708]

1 hour ago, Petermuc3 said:

sim = A319

ui_createdby= Flight Sim Labs

ui_manufacturer=Airbus

Peter

That's the expected info. But "mce.exe" has only been updated for that purpose recently.

Make sure you install the very latest version and we'll take it from there.

Flows won't appear for the A319, but could copy them from the A320 folder and adjust them as you see fit.

 

[FS++ 708]

22 hours ago, Petermuc3 said:

sim = A319

ui_createdby= Flight Sim Labs

ui_manufacturer=Airbus

Peter

I assume aircraft is now properly identified and fully supported.

[Petermuc3 8]

Gerald,

I did just one short flight with the latest MCE and the A319X. Overall It is working nicely, even

setting Heading/VS. A couple of things I could not get to work.

F/O cannot manipulate

- Engine Mode Selector

- Parking Brake

- disarm spoilers, arming works

- weather radar

-dialing speed, can push/pull speed knob

During FLCT check, I push aileron left, F/O reads "rudder full left"

Peter

 

[FS++ 708]

51 minutes ago, Petermuc3 said:

Gerald,

I did just one short flight with the latest MCE and the A319X. Overall It is working nicely, even

setting Heading/VS. A couple of things I could not get to work.

F/O cannot manipulate

- Engine Mode Selector

- Parking Brake

- disarm spoilers, arming works

- weather radar

-dialing speed, can push/pull speed knob

During FLCT check, I push aileron left, F/O reads "rudder full left"

Peter

 

Use the very latest "mcfslA3X.dll" (version 1.0.5.9) included in patch on this thread.

Just don't replace "mce.exe"

latest release still uses older dll.

Not sure I understand this "dialing speed, can push/pull speed knob"

 

 

[Petermuc3 8]

Will try that. F/O can push/pull speed knob but is not dialing the requested speed;

e.g. "set speed 210" F/O pulls out of managed speed but is not dialing 210, actually not dialing

anything.

[FS++ 708]

29 minutes ago, Petermuc3 said:

Will try that. F/O can push/pull speed knob but is not dialing the requested speed;

e.g. "set speed 210" F/O pulls out of managed speed but is not dialing 210, actually not dialing

anything.

He can't dial SPD on ground.

He should be able to handle it once airborne (provided he can read current speed).

By default, he'll try to work out the speed when passing 5000 feet above ground.

[Petermuc3 8]

I know, but this was on FL230.

[Petermuc3 8]

The A319X is now working quite nicely. Three things I still recognized

- FCTL check as described above

- "gear down" F/O is questioning wether speed is too high but I am well below VLO

- no dialing of speed irrespective of Altitude/FL

Peter

[Bob_Z 30]

 

New to MCE and slightly confused.  I have version 2.7.6.8. Do I need to install the the things included in the MCE2768 cited in this thread?

[FS++ 708]

49 minutes ago, Bob_Z said:

 

New to MCE and slightly confused.  I have version 2.7.6.8. Do I need to install the the things included in the MCE2768 cited in this thread?

V2.7.6.8 refers to "mce.exe" version.

Because some items were broken since FSL released V260, you need the more up to date "mcfslA3X.dll in \Prepar3D v4\MCE dlls\ folder.

Download the patch, then replace just the dll that fixes engine master, radar switching and a couple of other reported issues in this thread.

My guess, main installation package will be updated before the end of the week to include most recent dlls.

 

[Bob_Z 30]

Thanks.  I guess I can wait for the update. 

[757FO 143]

Is there a way to stop MCE from doing things like popping the FMGS, GSX, etc. on startup? I find it annoying as I am in the middle of prepping a flight and starting MCE interfere with my data entry.... Also, any ways to stop MCE to pop up the doors page (From Options and closing doors after GSX is done with boarding?)

Thank you!

John.

[FS++ 708]

10 hours ago, 757FO said:

Is there a way to stop MCE from doing things like popping the FMGS, GSX, etc. on startup? I find it annoying as I am in the middle of prepping a flight and starting MCE interfere with my data entry.... Also, any ways to stop MCE to pop up the doors page (From Options and closing doors after GSX is done with boarding?)

Thank you!

John.

Affirmative.

 

Go to \Prepar3D v4\MCE dlls\ and open "mcfslA3X.ini"

Add option "NoCduAction=1" to the [OPTIONS] section. Anywhere within that section.

 

[757FO 143]

4 hours ago, FS++ said:

Affirmative.

 

Go to \Prepar3D v4\MCE dlls\ and open "mcfslA3X.ini"

Add option "NoCduAction=1" to the [OPTIONS] section. Anywhere within that section.

 

Perfect, thank you Gerald

[Petermuc3 8]

With the latest MCE and the latest mcfslA3X.dll I still have the following problems

- "gear down" F/O questions too high speed which is not

- "fuel pumps on" Left FP Engine 1 does not get switched on

- "Flight Control Check" Aileron left F/O says "Rudder full left"

 

Thanks Peter