Petermuc3

Thanks Maxime, I was reluctant to update as I have a very stable sim right now. Peter

I bought it but it did not install into the sim. I am running P3D5. 1. Is version 5.3 required. SimMarket just states that version 5 is needed. Peter

Hi, I downloaded all files from flyaway simulation. I want to install it into P3Dv5 sitting in E:\P3D5. I started the installer for volume1 and it only offers me an installation in c:\FSX or P3D which I am not able to change. I did not go further being afraid messing things up. Any help is much appreciated. By the way there was no PDF in the download. Peter I was overlooking the initial installation path where of course I can select a different folder.

Simbrief does already a lot of that. Peter

Most airlines I know of would fly the climb with altitude constraints in managed mode; meaning the aircraft will fly what you have programmed into the FMS. Let's assume you are cleared to FL 120 but there are altitude contraints of 5000, 7000 etc. you dial in 12000 and push the altitude knob. The ac will start to climb and respect the constraints automatically. This is what the FSLabs Bus and the real aircraft do. I do not have the Aerosoft Bus but I assume she would do the same as this is a pretty basic function. Dialing in constraints as they come and pulling is called selected mode, I don't know of any Airbus pilot who would do that. Have fun with the Bus, it's a great aircraft. Peter

I have it and it is very nice, love to fly the RNAV 17C. No problems with the performance, flying the approach with FSLabs Bus. Peter

@Christoph I got it installed, looks very good. Thanks again for the help. Peter

Thanks a lot Christoph, I'll try tomorrow. Peter

Thanks Christoph, I think I made the mistake by just deleting the LOWS folder and then deleting the scenery withhin the AddonOrganizer. As I have reinstalled v1 now I will uninstall it correctly and remove it withhin the PAO. Would that be sufficient for a new install? Peter

Did anyone install LOWS already? I tried 2 times and it is not installing, even so it says that it has been installed correctly. P3DAddonOrganizer shows the scenery. One thing during the installation I need to repair my SODE engine; didn't have that with any other scenery installation. Reinstalled v1 with no problems. Peter

Frederico, I didn't have a single CTD since, still using 1.0.0.2. Thank you very much Peter

Hi guys, I am experiencing CTDs showing ATCAPI.dll as the fault module. This was with the FSLabs A320 in Athens. I have seen some comments concerning problems when you change the time, which I didn't. Of course Athens is 1 hour ahead of us here in Germany. Happy new year. Peter

I bought Canada West and Whitehorse. 30 minutes later I got e-mails with download links and serial. Installed and put my plane on various places, did some t/gs in Whitehorse and I really like it. That is why I always visit Avsim, I probably would have never found these sceneries. Thank you guys. Peter

Thanks, I'll give it a go. Peter

How is the purchase delivered? Is there any download option after purchase? Peter

@ Frederico Works great now. Thank you very much for the help and the wonderful tool. Peter

Hi, I used ATCAPI the first time today. EDDM-EDDN I configured for depart/land EDDM 08R/08L and for EDDN 10. I must have done something wrong, because 95% of the traffic departed and landed on 26L, the rest on 08R. I watched the traffic on my Aivlasoft EFB ground chart for about 20 minutes, but nothing changed. <?xml version='1.0' encoding='utf-8' ?> <Parameters> <Airport> <ICAO>EDDM</ICAO> <ActiveTakeOffRunway> <Runway>R08R</Runway> <Probability>0.5</Probability> </ActiveTakeOffRunway> <ActiveTakeOffRunway> <Runway>R08l</Runway> <Probability>0.5</Probability> </ActiveTakeOffRunway> <ActiveTakeOffRunway> <Runway></Runway> <Probability></Probability> </ActiveTakeOffRunway> <ActiveLandingRunway> <Runway>R08R</Runway> <ApproachName>OSDER</ApproachName> <ApproachType>ILS</ApproachType> <Probability>0.5</Probability> </ActiveLandingRunway> <ActiveLandingRunway> <Runway>R08l</Runway> <Probability>0.5</Probability> </ActiveLandingRunway> <ActiveLandingRunway> <Runway></Runway> <Probability></Probability> </ActiveLandingRunway> </Airport> <Airport> <ICAO>EDDN</ICAO> <ActiveTakeOffRunway> <Runway>R10</Runway> </ActiveTakeOffRunway> <ActiveLandingRunway> <Runway>R10</Runway> </ActiveLandingRunway> </Airport> <enableFastTakeOffs>1</EnableFastTakeOffs> <allowTakeOffDistance>4000</AllowTakeOffDistance> <taxiSpeedLimiter>30</TaxiSpeedLimiter> <enableRollthenTakeOff>1</enableRollthenTakeOff> <minCrossingRny>2000</minCrossingRny> <isGUIVisible>1</isGUIVisible> <deployEarlyFlaps>0</deployEarlyFlaps> Thanks for the help. Peter </Parameters>

Thanks Andi, so there is no solution yet? Peter

Hi, when I turn EA on I cannot see any snow, turning EA off no problem. Is this a known issue and is there a way to make it work? I am using the latest P3D5.1, ActiveSky and ASCA. Thanks Peter

Hi, is anyone using Envtex and ASCA? Does this improve the visuals compared to just using EA? I read somewhere that with EA on, Envtex will be overwritten, ASCA I am not sure. Any input is much appreciated, may be also the settings you use. Peter

I bought a relatively cheep USB heaset and everything is working fine now. Copilot's voice is now routed through the speakers as all the other sounds also, IVAO ATC is routed to the headset and no lower volume when ATC is kicking in. Peter

Thanks for the advice, Gerald. Actually I made some progress, MCE is now routing Copi's voice to my headset and the volume level stays up during ATC chatter. Funny thing is that GSX voices turn down instead, which come out of the speakers like the rest of the sound. So doesn't seem to be a MCE specific problem. I would like to have MCE also on the speakers, but will see. I assume problem is with Win10 or the audio controller of my mainboard msi MPG Z390 Gaming Pro. Yes I am on the latest MCE. Peter

Yes, but then again it works for a while and after a couple of minutes it stops again. I think MCE is not recognizing my voice, no red bar on the left top of the screen. Checking the sound controls the mic is OK. Would an USB headset be better? Peter By the way would it be better to enable WHQL in Bios to allow other drivers to be installed. I am far from being a computer geek, so that might be nonsense.

I think that I have a more complex issue with MCE. It is not only that the Copi's voice level gets low, after a while I completely loose my Copi. Looking at my sound settings my mic is working. Peter

Thanks guys, I already have done the "do nothing option" to no success. @Dimitrios in Narrator I have unticked "Lower the volume..." to no success. But I think Narrator is off anyways. It would be great if you could have a look into your "focus assist" settings and tell me what they are. Peter