Jump to content

Archived

This topic is now archived and is closed to further replies.

Jason.A

SP1 still getting Crash on exit

Recommended Posts

Me too !I have always had this since the very first day.It does not bother me now because it's only if I end the flight.I just close the FSX window instead.Fred.

Share this post


Link to post
Share on other sites

its worse when you get it on load up, I have a bad problem with this, even after complete reinstall, have load up another plane then select the NGX

Share this post


Link to post
Share on other sites
its worse when you get it on load up, I have a bad problem with this, even after complete reinstall, have load up another plane then select the NGX
Have you delete manual the folder of PMDG after uninstall the 737ngx?

Share this post


Link to post
Share on other sites

Also getting this, every time I shut down the sim after using the NGX. It says the PMDG.DLL failed. Will capture exactly the message next time.

Share this post


Link to post
Share on other sites

i have tried any of the suggestions posted here and in other forums, the issue still persists.Not a bit deal really, im amazed at how well the NGX flys/performs considering the scope and complexity of the simulation.Just a litte gripe, and wanted to make sure PMDG were aware of it :)Happy contrails to all

Share this post


Link to post
Share on other sites
Have you make the changes in fsx.cfg as Ryan says and add the uiautomationcore.dll in the fsx directory?
Good morningSame problem here. But maybe i missed something from Ryan. What was the issue of this maybe with uiatomationcore.dll?Thanks and best regardsMarcel

Share this post


Link to post
Share on other sites

exactly the same problem here! what about the changes in fsx.cfg and uiatomationcore.dll? where can i find this and what to do in the fsx.cfg file?

Share this post


Link to post
Share on other sites

Guys, those who have these various problems?Did you try reformatting (you do know you can back-up your system and have it back to the saved situation inside of minutes with imaging tools?), installing Windows7 64bit all anew, fresh FSX and then NGX. Does it crash then?What I love about all these threads that NGX doesn't run well, crashes etc, is that you never ever check the software on a fresh config, to confirm that the problem is not in the software you are accusing?

Share this post


Link to post
Share on other sites
eeeeerrrr...reformatting an O/S should NOT be a solution to this problem.
If you maybe re-read my post, you will notice I said "back-up" - that means it's only to test to definitely find out if it's the NGX or your system, software or hardware side.

Share this post


Link to post
Share on other sites

Yes, you also said reformat, installing Windows7 64bit all anew, fresh FSX and then NGX. This IS over the top for the solution.

Share this post


Link to post
Share on other sites

I had this problem using Super-Sampling, once it was turned off, back to Adaptive Multi Sampling the problem went away.

Share this post


Link to post
Share on other sites
Yes, you also said reformat, installing Windows7 64bit all anew, fresh FSX and then NGX. This IS over the top for the solution.
Yes, I did - apparently you misunderstood and don't know what system imaging is.

Share this post


Link to post
Share on other sites
Yes, I did - apparently you misunderstood and don't know what system imaging is.
Thanks, Move on - life's too short.

Share this post


Link to post
Share on other sites

OK. My NGX is working perfectly, so I just wanted to help. Apparently you are not interested.

Share this post


Link to post
Share on other sites

I also have the same problem after SP1. Upon exiting - it crashes. I did not however do a re-install. I simply downloaded and installed SP1. All else works perfectly. The crash is not a problem since I am, exiting anyway, but it does worry me that this problem will manifest into a crash all the time.

Share this post


Link to post
Share on other sites

×
×
  • Create New...