Hi Morgan,If you want to have the updated sids/stars etc, yes.You can if you know it, or you can put in whats expected to be the arrivaldelete any discontinuity and check the rnp against the required rnp for departure

ok, so having the current AIRAC is NOT necessary for the FO to accept the CDU settings on the checklist ?I need to study up on checking the 'rnp against the required rnp for departure' that you are talking about.Too bad the FO cannot just tell me what it is in the FMC he does not jive with. Oh well.

No it's not.That's for rnav departures

I found a button setting that was causing my 2-D cockpit to switch to VC. So that is solved and NGX loads up with no problems in 2-D.FO saying 'you might want to check that' about my CDU/FMC setup. What values MUST be entered before FO is happy with the CDU ?

Hello.I'm curious what button setting you found as I am having the same issue of it automatically switching. I have the 2-D setting set, and it does load, but without any action from me, it changes to the VC.Tim Hendrickson

Hello.I'm curious what button setting you found as I am having the same issue of it automatically switching. I have the 2-D setting set, and it does load, but without any action from me, it changes to the VC.Tim Hendrickson

I thought it was 'button 2' on my Saitek Pro Flight Yoke... but now I am thinking it is something to do with my old 'view' settings in FSX (which I am going to clear out completely) and ezdok. Are you using ezdok ?

I thought it was 'button 2' on my Saitek Pro Flight Yoke... but now I am thinking it is something to do with my old 'view' settings in FSX (which I am going to clear out completely) and ezdok. Are you using ezdok ?

I am, yes.Tim Hendrickson

When I get home from work I may try turning off EZDOK and loading the NGX to see if that is what is causing it to switch back to VC after a few seconds. Although... even if it does switch back, isn't it technically still 'loading' in 2-D ? Too many add-ons at one time is making my head hurt. :(

1) Fs2Crew will close the cargo doors when the ground crew is done.2) Taxi and takeoff brief is the same as the Departure brief (it's basically a reminder)3) You didnt announce the start sequence, you should say "start sequence is 2 then 1" etc

1) OK I wait for T+0 and then check doors/before start check list3) How can I announce the start sequence in button control version?Airwolfe: Don't worry about ezdok. I dont have ezdok, but I have same problem (unable to start engine 2) as yours. I don't have automatic switch to VC problem.If I understand clearly nobody know what is behind original problem? (in 2D mode also unable to start engine 2)

Airwolfe: Don't worry about ezdok. I dont have ezdok, but I have same problem (unable to start engine 2) as yours. I don't have automatic switch to VC problem.

What livery are you using ? When I switched to the PMDG House livery I was able to get the engines started.

What livery are you using ? When I switched to the PMDG House livery I was able to get the engines started.

I only have the PMDG House livery.Tim Hendrickson

I only have the PMDG House livery.Tim Hendrickson

Everyone, if you're still having engine start problems....Try this:http://forum.avsim.n...issue-try-this/

Hi allCurious, in my case was the Edzok Camera Tool the mistake! After I set the tool to disable before I load the NGX in 2D and FS2Crew, I don't have any problem.Best Regards from SwitzerlandOliver

I have ezdok and don't have any problemsI have ezdok and don't have any problems

computers drive me insanecomputers drive me insane :( :(

Everyone, if you're still having engine start problems....Try this:http://forum.avsim.n...issue-try-this/

Thanks byrok. My problem solved. My SP1c was wrongly installed generate my problem.If I try to install SP1c again not allow they say same version number. But if I follow your instructions works well.The only point what I see difference after install done: FMC/PMDG Simulation just see one FO callouts before and three V1,VR,V2 after that.So my cause was PMDG SP1c not installed succefully. Reinstall solve issue.From another happy FS2Crew customer :(

Glad you got it solved!SP1C clears many issues!