February 4, 201313 yr Hey guys I was wondering if maybe there was an easier way to fix this problem that I am having, I have tried uninstalling it ultimate train I have tried uninstalling misty and tongass and then just reinstalling misty and and Tongass Without Ultimate Terrain Canada I am also seeing this problem somewhere in the Bahamas as to where I get buildings on water I have installed the misty patch HitFix a lot of problems but I'm still getting this specific problem. This is OP1 camp from Avsim it's said it's fully compatible with UT, Misty, and Tongass so I'm not certain of what may be causing the problem. Any ideas?
February 4, 201313 yr Did you remember to run the restore the defaults in UT before you uninstalled it? The double shore lines and such indicate that and perhaps scenery priority issues as well. Regards, Mel
February 4, 201313 yr Author Ok what so you mean by scenery Priority issue? By that I'm guessing your referring to the sequence as to how I activated my scenery within FS9 or could the problem also originate from the scenery CFG?
February 4, 201313 yr Also check any recently installed scenery. Sometimes it will push other areas into conflict (displacement).
February 4, 201313 yr Author Ok I found the problem, Seems like the problem was the misty fjords landscape interfering with Tongass scenery, Every time I disabled the misty Fjords land class The problem goes away every time I enable it the problem is back. So I did a little research and I found a solution I'm not sure as to why its interfering but the problems that interfering has to do with 4 files in the misty Fjords Land class folder. I deleted the files then Re- enabled the Misty landClass and Eureca problem solved and everything is working well. The files are O_U_T HP912120.bgl O_U_T HP913120.bgl O_U_T HL913120.bgl O_U_T HL912120.bgl If it renamed these BGL,S why is it interfering?
February 4, 201313 yr Did you run the configurators for Misty and Tongass? If so, did you tell them you have UT? These programs all work together if you set them up correctly. Without the need to manually move files. If all else fails, read the instructions. regards, Joe The best gift you can give your children is your time.
February 4, 201313 yr Commercial Member In my experience, these are incredibly finicky scenery packages to install. I've reinstalled a few times until I got it right, and my order of install was UT, then Misty, then the Misty/UT patch, then Tongass (run config), then Glacier Bay (run Glacier config, then Tongass config). I'm not entirely sure, but I have had UT coastlines show back up after reapplying UT options, which was cured by a reinstall of Tongass. My rule is now is, if it's not broke, don't touch it! Jim Stewart Milviz Person.
February 4, 201313 yr I deleted the files then Re- enabled the Misty landClass and Eureca problem solved and everything is working well. If it renamed these BGL,S why is it interfering? Probably the coastline bgls from one being different than the other hence the multiple coastlines. Regards, Mel
February 4, 201313 yr Author Hey guys yes I did run the configuration tool And I've also manage to find the patch for misty Fjord to be compatible with ultimate terrain Canada, Running the ultimate terrain Canada misty Fjord patch fixed a lot of the land class problems that I was encountering with misty, After deleting the files that I posted above all my problems with the double shorelines disappeared and also the problem with the cabins floating on the water, I also found out the issue that I was having at the Bahamas as to where I was having also buildings floating on top of the water, But that was an entirely different situation has nothing to do with Misty or ultimate terrain USA. After days of research and configuring I finally got everything to look perfectly fine, There are only 2 minor issues that I'm currently having, And they are 1. When running tongass configurator I tried to select Freight dogs which I also have installed in my simulation After applying it it says that he can't find the path to the scenery airport directory of the Freaight dogs when I hit browse to set the path it's already there,the scenery seems to be working just fine I'm not sure why the configuration tool for tongass does not except it 2. And also when I installed the little port walter scenery the elevation of the terrain is not correct , I enter the values as instructed to do so inside the read me. Txt but when done it raises the terrain with water so I just deleted the house and put a beach house in place of it. Other then that everything else seems to be ok Hey guys yes I did run the configuration tool And I've also manage to find the patch for misty Fjord to be compatible with ultimate terrain Canada, Running the ultimate terrain Canada misty Fjord patch fixed a lot of the land class problems that I was encountering with misty, After deleting the files that I posted above all my problems with the double shorelines disappeared and also the problem with the cabins floating on the water, I also found out the issue that I was having at the Bahamas as to where I was having also buildings floating on top of the water, But that was an entirely different situation has nothing to do with Misty or ultimate terrain Canada. After days of research and configuring I finally got everything to look perfectly fine, There are only 2 minor issues that I'm currently having, And they are 1. When running tongass configurator I tried to select Freight dogs which I also have installed in my simulation After applying it it says that he can't find the path to the scenery airport directory of the Freaight dogs when I hit browse to set the path it's already there,the scenery seems to be working just fine I'm not sure why the configuration tool for tongass does not except it 2. And also when I installed the little port walter scenery the elevation of the terrain is not correct , I enter the values as instructed to do so inside the read me. Txt but when done it raises the terrain with water so I just deleted the house and put a beach house in place of it. Other then that everything else seems to be ok
February 5, 201313 yr yeah... there are some problems with the configurators. Unfortunately. The best thing to do is to keep track of what files get moved where when you use the configurators - then kinda hand-build your own version. It can be tedious, but it is worth it. Glacier Bay and Tongass work together flawlessly - and they also work together perfectly with Freight Dogs. However, when you add Misty and UT and Vancouver+ and FSGenesis meshes and the Columbia River Gorge and British Columbia - well, it gets messy. I've got all of those and more installed - and I've had to rebuild my various shorelines by hand more than once. (The worst was one time where somehow the entire waterclass for Alaska got misplaced. Then there weren't ANY coastlines and the boats were plowing through trees!) When that's all done, though, it's done. There will probably never be a reason to change anything again. And boy, was it worth it! I love what I've got now. Beautiful stuff. I can fly from Valdez (AK) all the way down past Portland to Spokane in beautiful Sandmann scenery now... (with Flightzone and a large number of Georenders and FSAddon New World Series sceneries in there, too... If you want to know what a tragedy is, go google FSAddon Orcas Island - IMHO, that's THE best addon scenery that isn't sold anymore!)
February 5, 201313 yr that's THE best addon scenery that isn't sold anymore! Agree ... but partnered with the nearby Emma Field, the original Richard Goldstein masterpiece. To the OP. You might also check your Terrain Mesh setting in the cfg. An 'incorrect' setting can also contribute to objects appearing in the water/sea.
February 5, 201313 yr Author Hmmm I haven't mess with the Terrain.cfg I may take a look at it, I know one thing though the terrain settings within my FS9.cfg always resets itself to a large number no matter what I do
Create an account or sign in to comment