Jump to content

Archived

This topic is now archived and is closed to further replies.

csf1209

FO cannot run Descend Flow

Recommended Posts

 I have a problem with my FS2CREW 777. According to the manual, 

when Approach Brief was completed, FO should run his Descend Flow. But sometime my FO does not do that. Anyone know what is the problem? 

 

It works when I test on the ground. Unfortunately, when I was flying a flight,It will not work!

 

Thanks

 

Share this post


Link to post
Share on other sites

are  you doing the approach brief  within  50 to 100 nm of  the tod


I7-800k,Corsair h1101 cooler ,Asus Strix Gaming Intel Z370 S11 motherboard, Corsair 32gb ramDD4,    2  ssd 500gb 970 drive, gtx 1080ti Card,  RM850 power supply

 

Peter kelberg

Share this post


Link to post
Share on other sites

You mean you're following the manual.

I refer to the manual(FS2Crew PMDG777 Manual.pdf page 32-42) for the installation of the software.

Share this post


Link to post
Share on other sites

are  you doing the approach brief  within  50 to 100 nm of  the tod

yes, i doing the approach brief with 50nm below of the tod

are  you doing the approach brief  within  50 to 100 nm of  the tod

yes, i doing the approach brief with 50nm below of the tod

Share this post


Link to post
Share on other sites

What happens if you call for "Descent checklist" ?


What happens if you call for "Descent checklist" ?


Romain Roux

204800.pngACH1179.jpg

 

Avec l'avion, nous avons inventé la ligne droite.

St Exupéry, Terre des hommes.

Share this post


Link to post
Share on other sites

What happens if you call for "Descent checklist" ?

What happens if you call for "Descent checklist" ?

Will work normally, but the brakes and the app speed will not be selected.

 

After landing,select TAXI LIGHT OFF,Taxi and Runway Turnoff  will not help me off

Share this post


Link to post
Share on other sites

when Approach Brief was completed, FO should run his Descend Flow. but can't be on the display panel to see <-Descent Flow-> .

Share this post


Link to post
Share on other sites

Silly question, do you wait long enough between doing the approach brief and the descent checklist? It can take a while for the FO to setup the aircraft for the descent (I don't remember how long but they don't start the descent flow immediately after the briefing).


Romain Roux

204800.pngACH1179.jpg

 

Avec l'avion, nous avons inventé la ligne droite.

St Exupéry, Terre des hommes.

Share this post


Link to post
Share on other sites

My apologies for the thread crept, but every time I see this title it reminds me of a FO I flew with a while back.    :smile:


I Earned My Spurs in Vietnam

Share this post


Link to post
Share on other sites

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    34%
    $8,560.00 of $25,000.00 Donate Now
×
×
  • Create New...