October 25, 20178 yr Last three months, I am having a major problem with Control, Axis, Calibration and FSUIPC settings with my all planes. I went through all problem solving possibilities none of them fixed the problem. I cannot fly . I just run the repair for P3D v4.1. No luck. What I suppose to do? I deleted FSUIPC no result. I have CH Pedals & Eclipse Yoke. I uploaded latest CH Control Manager, No lucks. Do I need to replace CH pedal and yoke. If yes what do you advise? Thanks Ahmet Sanal "Time you enjoyed wasting, was not wasted"
October 25, 20178 yr 7 minutes ago, asanal said: Last three months, I am having a major problem with Control, Axis, Calibration and FSUIPC settings with my all planes. I went through all problem solving possibilities none of them fixed the problem. I cannot fly . I just run the repair for P3D v4.1. No luck. What I suppose to do? I deleted FSUIPC no result. I have CH Pedals & Eclipse Yoke. I uploaded latest CH Control Manager, No lucks. Do I need to replace CH pedal and yoke. If yes what do you advise? Thanks I stopped using the CH control manager a couple of years ago and uninstalled it. I have CH Pedals and I use FSUIPC to set and calibrate all my axis for the many different types of planes and copters I use. .
October 25, 20178 yr Author Bob, thanks for your response. I tried use FSUIPC , but I didn't succeeded. I printed the Guide Manual, but I cannot follow up the manual. It is written for people who has good knowledge about FSUIPC. What did you replaced CH Yoke? Ahmet Sanal "Time you enjoyed wasting, was not wasted"
October 25, 20178 yr 31 minutes ago, asanal said: Bob, thanks for your response. I tried use FSUIPC , but I didn't succeeded. I printed the Guide Manual, but I cannot follow up the manual. It is written for people who has good knowledge about FSUIPC. What did you replaced CH Yoke? Hi-there are only 3 or 4 pages of the instructions in FSUIPC dealing with axis assignment and calibration. Pull them out to read and ignore the rest of the instructions. I couldn't understand the rest either, but that part is straightforward and it works. Forever indebted to the late Michael Greenblatt of FSGS.
October 26, 20178 yr 2 hours ago, asanal said: Bob, thanks for your response. I tried use FSUIPC , but I didn't succeeded. I printed the Guide Manual, but I cannot follow up the manual. It is written for people who has good knowledge about FSUIPC. What did you replaced CH Yoke?
October 26, 20178 yr Author Bob, that is the one I spent so much time and not finished the settings. I have to re-install FSUIPC and will try again. Do you have any idea about this yoke "Logitech - Saitek Pro Flight Yoke System" ? Thanks Ahmet Sanal "Time you enjoyed wasting, was not wasted"
October 26, 20178 yr Author Bob, that is the one I spent so much time and not finished the settings. I have to re-install FSUIPC and will try again. Do you have any idea about this yoke "Logitech - Saitek Pro Flight Yoke System" ? Thanks vp49p3 I will re-read those pages and will try again. Will inform. Thanks Ahmet Sanal "Time you enjoyed wasting, was not wasted"
October 26, 20178 yr Author I gave up for tonight. FSUIPC settings , Ailerons connected to Mixture control. Ahmet Sanal "Time you enjoyed wasting, was not wasted"
October 26, 20178 yr Moderator http://fsuipc.simflight.com/beta/SIMSAMURAI+FSUIPC+TUTORIAL.pdf I found this very easy to understand and use and he gives good diagrams and examples. Just take it slow and easy. Vic RIG#1 - I9 14900K MSI Pro z790 RTX 5070Ti 40" 4K Monitor 3840x2160
October 26, 20178 yr Author Vic, thank you. Tomorrow I will work on it. Ahmet Sanal "Time you enjoyed wasting, was not wasted"
October 26, 20178 yr Author Here is the this morning's results: 1- FSUIPC controls Ailerons, elevators and ruder accordingly. 2-In same time connects ailerons to Mixture control and Elevators to throttle. It looks like a I am experiencing some kind major problems which are preventing FSUIPC to functions correctly and messing up P3D Axes Controls . I gave up. My last questions: How can I clean P3Dv4.1 and FSUIPC from these problems ? 1- Will I uninstall P3dv4.1 and start fresh? 2- Will I delete all FSIUPC and files from my PC 3- Will I uninstall Windows 10 and all addons ? Thanks Ahmet Sanal "Time you enjoyed wasting, was not wasted"
October 26, 20178 yr Hi Ahmet Have you gone through the controls section in P3D and made sure that your axes are not configured to something there too? This has tripped me up in the past - you have to go through each controller and ensure that it is not assigned to anything. Then you should be able to assign them in FSUIPC and there will be no conflict. You've probably already done that but just making sure! Cheers Stu Stuart Furley
October 26, 20178 yr Author Stu, thanks for your response. I re-checked P3D controls section none of the axes are assign to anything. Ahmet Sanal "Time you enjoyed wasting, was not wasted"
October 26, 20178 yr Go for a reinstall, of fsuipc just Check you have downloaded a 'complete ' install of fsuipc5, 5121b and then update to 5121c Bob
October 26, 20178 yr Author Bob, Will I delete all files from Module folder, Then install 5121c? Ahmet Sanal "Time you enjoyed wasting, was not wasted"
Archived
This topic is now archived and is closed to further replies.