March 8, 20224 yr Hi folks. As far as I can tell, I installed and set up AIG the correct way. I downloaded and installed something around 1250 flightplans. I installed the AIG Traffic Controller software as well. I believe I pointed everything correctly to the library. However, when I set up a flight and go to the traffic controller and inject, I don't see much happening. I don't see any additional planes appearing, I don't see any plane movement on the ground. No taxiing, no planes taking off or landing. I have reviewed the instructions for installation and operation and I don't see anything that I am doing wrong. Can I get some advice from some of you AIG users on what I should maybe check? I am mostly using KLAS (McCarren Airport) to test but I also tried Dallas-Ft.Worth. I have never seen a plane moving. Help please .......... Thanks ..... Rob I should add that I installed the fix to get GA traffic back so that the sim controls GA traffic and AIG controller airliner traffic. Edited March 8, 20224 yr by Rob G Additional info Case: (Lian Li PC-011 Dynamic XL), PSU: (MEG Ai300p pcie 5 & ATX 3.0), Motherboard: (ASUS TUF Gaming x670E-PLUS WIFI 6E), CPU: (AMD Ryzen 7 7800-X3D) Memory: (G.Skill Trident Z5 NEO RGB Series 64GB DDR5 6000), GPU: (Zotac Gaming GeForce RTX 4090 AMP Extreme Airo). CPU Cooler: (ASUS ROG Strix LC RGB 360) Fans: (7 Corsair LL Series 120mm RGB)
March 8, 20224 yr When do you run the AIG Traffic Controller ? I found it works fine if you just run it when you spawn into the aircraft on the airport. it then takes a minute or so, and you should see aircraft spawning at the gates, and traffic either landing or taking off, etc. AMD Ryzen 7 5800x3d, MSI X570 Pro, 32 gb DDR4 3600 ram, Gigabyte 6800 16gb GPU, 1x 2tb Samsung NvMe , 1x 2tb Sabrent NvME, 1x Crucial 4tb Nvme M2 Drive
March 8, 20224 yr 1 hour ago, Rob G said: Hi folks. As far as I can tell, I installed and set up AIG the correct way. I downloaded and installed something around 1250 flightplans. I installed the AIG Traffic Controller software as well. I believe I pointed everything correctly to the library. However, when I set up a flight and go to the traffic controller and inject, I don't see much happening. I don't see any additional planes appearing, I don't see any plane movement on the ground. No taxiing, no planes taking off or landing. I have reviewed the instructions for installation and operation and I don't see anything that I am doing wrong. Can I get some advice from some of you AIG users on what I should maybe check? I am mostly using KLAS (McCarren Airport) to test but I also tried Dallas-Ft.Worth. I have never seen a plane moving. Help please .......... Thanks ..... Rob I should add that I installed the fix to get GA traffic back so that the sim controls GA traffic and AIG controller airliner traffic. This sounds like a database error. Delete the zip file and let it create a new one by loading AIG TC when at the ramp. There seems to be a bug in the latest version of TC that corrupts the database. I'm only sharing this because you downloaded 1250 FPs. I feel bad for you. MSFS
March 8, 20224 yr There is a s a suggestion on one of the how to videos posted on Avsim that you should just download a couple airlines and test first. For example, download EasyJet and go to one of their hubs to check traffic is loading there. Better than downloading 1200 flight plans/airlines and then finding out the setup is gone wrong somewhere. GregH Intel Core i7 14700K / Palit RTX4070Ti Super OC / Corsair 32GB DDR5 6000 MHz / MSI Z790 M/board / Corsair NVMe 9500 read, 8500 write / Corsair PSU1200W / CH Products Yoke, Pedals & Quad; Airbus Side Stick, Airbus Quadrant / TrackIR, 32” 4K 144hz 1ms Monitor
March 8, 20224 yr Author 4 hours ago, DJJose said: This sounds like a database error. Delete the zip file and let it create a new one by loading AIG TC when at the ramp. There seems to be a bug in the latest version of TC that corrupts the database. I'm only sharing this because you downloaded 1250 FPs. I feel bad for you. Which zip file are you referring to? Case: (Lian Li PC-011 Dynamic XL), PSU: (MEG Ai300p pcie 5 & ATX 3.0), Motherboard: (ASUS TUF Gaming x670E-PLUS WIFI 6E), CPU: (AMD Ryzen 7 7800-X3D) Memory: (G.Skill Trident Z5 NEO RGB Series 64GB DDR5 6000), GPU: (Zotac Gaming GeForce RTX 4090 AMP Extreme Airo). CPU Cooler: (ASUS ROG Strix LC RGB 360) Fans: (7 Corsair LL Series 120mm RGB)
March 8, 20224 yr 2 hours ago, Rob G said: Which zip file are you referring to? AIG_TrafficController/Resources/ AIG_Databases_ (zipped) MSFS
March 8, 20224 yr I just recently installed AIG for MSFS and I do get planes all over the place which is great! AIG Traffic Controller is running all is good. The problem I am having is that only a few are taxing and taking off but most of them are just standing around or spinning around in circles doing pirouettes. Am I doing something wrong? Maybe I am missing a step or two or maybe this is an MSFS issue?
March 8, 20224 yr 1 minute ago, Ianrivaldosmith said: Correct. Thanks!..I figured that was the case...
March 9, 20224 yr Author Rather than deleting all of those flightmaps, I ran some of the maintenance tools provided and now things seem to be working as they should. Haven’t seen too many planes taking off and landing but at least a few and lots of planes at gates and meandering around the airport LOL. Case: (Lian Li PC-011 Dynamic XL), PSU: (MEG Ai300p pcie 5 & ATX 3.0), Motherboard: (ASUS TUF Gaming x670E-PLUS WIFI 6E), CPU: (AMD Ryzen 7 7800-X3D) Memory: (G.Skill Trident Z5 NEO RGB Series 64GB DDR5 6000), GPU: (Zotac Gaming GeForce RTX 4090 AMP Extreme Airo). CPU Cooler: (ASUS ROG Strix LC RGB 360) Fans: (7 Corsair LL Series 120mm RGB)
March 9, 20224 yr You can check an airport's departure and arrival schedule in the manager, by searching for the ICAO. The scheduled arrivals and departures will vary by time and date. Edited March 9, 20224 yr by Waldo Pepper
Archived
This topic is now archived and is closed to further replies.