tripo

Q400 without a doubt.

I have got a 27" BenQ 144hz monitor and I would like something a bit bigger, I have an 8086 with a GTX1080, Would I lose much performance by going to a 4K 32" monitor, and would it be noticeable going from a 144hz monitor to a say 60Hz setup. I have a really smooth stutter free experience in P3d v4, Would my GPU be capable of maintaining that by moving to 4K. Bill

(MB is an ASUS A7N8X-X. Suggestions welcome apart from "get rid of that ancient artifact".)I used to have an A7N8X, I think you can enable/disable onbord sound in the Bios, give it a try.Bill

I am running an E8600 @4.05ghz and using a 9600gt with a 22" widescreen 1680 X 1050, what would be the best card to suite this setup, my previous 8800gt bit the dust recently and the 9600 does not seem that much different. Using FSX of course.Bob

Try turning of "aircraft casts shadows on itself" in your display settings, I had this problem and it worked for me.Bill

I can thoroughly recommend FS-GS, amazing performance after the consultation, you would not think FS9 could look so good, and with high frame rates. Well worth trying.Bill

Hi, Yes you sure can, I use them both together, and they work perfectly.Bill

Same problem here, I have managed to get the FS9 version, but the FSX version is another story, I have now used up my three downloads, managed to get to 48% twice and earlier on it failed at 30%!!.This is not a very good situation, they need to get things sorted out.Bill

Hi,I had a similar problem with the demo and the release version, I re-calibrated the pedals in CH Manager and it cured the problem.Bill

Damian,Many thanks for the prompt reply, that did the trick, looking forward to the FSX version.Many ThanksBill

Hi, I tried ASv6 with FSX and as you say it works ok. One question, the visibility remains the same at altitude as it is on the ground eg. EGSS was giving 4500mtrs in haze, when I climbed up to eventually FL310, the viz was the same, occasionally, things cleared for a millisecond but generally stayed in haze. Is this an issue that will have to be dealt with when you bring out the patch for FSX or is there a setting somwhere to overcome this.I have tried various settings ie, changing viz max range etc but nothing seems to make any difference.Bill

Dean,Next day normally:)Bill

Bryan,You have done it again, what a wondefull piece of work. It compliments the 744 beautifully, it is so easy to use.This is a must get for anyone who flies the 744.Well done..Bill

Hornit,If you are talking about the bumpy taxiways, and the lack of parking here.AFIK the problem at NZCH is not in the AFCAD, I read somewhere that it is an issue with the secenery, apparently a fix is being worked on.I have tried different AFCAD's and no joy with any of them.Bill

>They probably took it down due to the endless stream of>complaints n the 737. it is beyond hope at this point.>JSWhat 737 are you referring to !! I've had it since day one, and it has been no worse than any other payware aircraft, if not better than some, all in all a very good package.Tripo

Great piece of software, works a treat here, the only problem is I cannot use the DF727 with the DLL installed, FS crashes after a few mins, it gives the fault as SIM1.dll, this only seems to happen with the DF727, but I have not tested every A/C in my FS installation.Bill

Hi,Earlier this week, I had an hour in a Full Motion 727-200 sim, and it is amazing how close the DF72 is to the sim, what a wonderful aircraft,It made life so much easier in the sim having done a few hours with the DF72.Well done Paul and the team, keep up the good work.Bill

My CH Yoke LE is showing signs of age, It has done a fair few hours, and is about four years old so I am thinking of replacing it.I like the look of the PFC Yoke (jet style) I was wondering if anyone has recently changed to one of these from a CH yoke, and what their views are on the PFC Yoke.Bearing in mind it is almost four times the cost, does it improve the feel and 'flyabilty' factor by much.Bill

Try FsNet, sounds like the thing you are looking for,although still in beta stage, it works quite well.http://www.gates.to/go.phpGood Luck Bill

I was just about to ask the same questions;)Bill

What a great Panel this is, I absolutely adore flying thie Aircraft.Since I installed the latest update, I do not seem to have the latest modifications to the panel, eg. cabin chimes etc, that new part of the panel does not show up, also the upper radio panel is not showing either.:) Any ideas ?Bill

David,"I can't remember what the 'OC' in 'OCA' stands for but the bold numbers are DH as shown on the baro altimeter and those in brackets ar Radio alt heights."OC = Obstacle clearanceOCA = Obstacle clearance AltitudeOCH = Obstacle clearance HeightCheersBill

Love em both, very nice:) Bill