bozflyer

Hi guys ! Based on my own experience, despite strong hardware you can mount, watch for your water quality slider ! It eats a huge amount of processor work and causes the hated blurrie texture problem even over hi FL ! I have set it on LOW end suddenly blurrie is disappeared..

I finally deleted the ENB series dll.. I found blurrie textures with it and worst, lot of crash to desktops ! you can even read on the intoruction manual of 777 that PMDG suggest to don't inject ENB series dll to avoid unpredictable behaviors.. I tryied it and removed it...

Hi pilots, I have a question about starting APU : I tryied to start the APU with battery power online only, no ground power connection. Wonder myself that this way it won't start.. if you listen from outside u can ear the spool up whistle but suddenly it goes down and APU won't stat.. Tryied second attempt : i set up ground connection dual power but without putting online with the overhead switches.. (you can read two green switches telling "AVAIL") only connected but not activated ! In this case the APU starts without problems.. ISSUE or PrOCEDURE ? anyone knows it ? Thank you a lot !

Hi pilots, I have a question about starting APU : I tryied to start the APU with battery power online only, no ground power connection. Wonder myself that this way it won't start.. if you listen from outside u can ear the spool up whistle but suddenly it goes down and APU won't stat.. Tryied second attempt : i set up ground connection dual power but without putting online with the overhead switches.. (you can read two green switches telling "AVAIL") only connected but not activated ! In this case the APU starts without problems.. ISSUE or POCEDURE ? anyone knows it ? Thank you a lot !

After running the Operation Center it updated but soon after it continuously ask the folder to find *.ptp texture files.. See the shot attached The program stays here freezed waiting the folder input but despite you tell it, nothing happens..i tried to sent it in : C:\Users\Bozz\AppData\Roaming\PMDG\PMDG Operations Center\Liveries but still ask the same.. no way to exit the Op Center otherwise you exit it from task manager... any idea ?

Route length is the distance you will fly...long routes allow higher flight altitude.

According to my own experience , the FL is dependig at least from two important variables1- Aircraft Wait2- route leghtIf you wait a lot ( 100% load of fuel) and/or full cargo and passenger and your route is long only 100 miles , the FMC calculate the flight profile according to those variables ( fliying low profile)Try to sta as low as you can with fuel and look for longer travel distances and will se also FL 380.

I own that video gpu..i am satisfied a lot , tryied some overclock but due to heat increase and low/unnoticeable results i decided to go to standard setup...That'it..Paolo bozzetti

I had same problem , i was used for my preference to change the "instrument transfer swithches" position. It MUST be all in CENTER position otherwise AIII do not arm.I was getting crazy but finally i coght the solution.Hope this help you.Paolo bozzetti

..should i add some more to the question ?In the HGS official manual is stated that during the approch fase the system alert the pilot flying with an alert visible on the combiner..is also this really simulated ? I know that active sky evol. Simulate wind shear...is this possible to see during approch wind shear alerts than ?Thank youPaolo Bozzetti

I never wonder enough about superficial and close mind exist !How can you say somthing like this ?

..scuse me ! I omitted to say i use Venice X addon airport.. So ILS Freq is 109.95 ...I tryed one more time taking off follow CHI SID and imediately landing ...it was all checked and setup but on final landing run at about 3-4 miles out the rnwy thershold the HGS showed no AIII...that's new to me...But at the same time i was near to solve the problem...Anyway i will try more touch and go to find a solution...as soon i solve it i will tell you.Thk very much for support till here !

Thnks first..I saw only one time all the visual cues landing in LIPZ Venice airport runway 04R..Exactly at 300 agl appeared the left and right visual lines duplicating runway limits...Ils identified at 109.95 course 40 deg on both...

Exactly what i setup carefully everytime...i am getting crazy about this.. All is ok but this strange behavior...!I feel frustrated and stupid to all of you..but it is... :-)

It happened to me when i had a poor video card while loading huge texture... Now i own a Nvidia 560 Ti and since i installed it no more strange blue glitches when changing views in fsx...Maybe fsx need time to load textures in memory meanwhile it shows this strange artefact..