Could i also get the Gauge, Jim ?

 

Regards from Greece

MFG2 Joerg

Hi

 

You certainly can have a copy, and as you probably know by now I have sent you a PM with the download link for the files and installation instructions.

 

As always, although you shouldn’t have any problems, but if you should then just let me know and I will try to help if I can.

 

Take care, and have fun.

 

Jim Hodkinson

Hi Jim,

I appreciate your devotion to your fellow simmers. I have recently purchased the LDS 767 and have similar problem with opening cargo doors. Can I have the gauge. Much appreciated.

 

İlhan KESMEZ

Hi İlhan

 

Firstly, thank you for the generous comments, I am not certain that they are deserved but they are appreciated, and secondly you most certainly can have a copy, and as you probably know by now I have sent you a PM with the download link for the files and installation instructions.

 

As always, although you shouldn’t have any problems, but if you should then just let me know and I will try to help if I can.

 

Jim Hodkinson

Hi Jim,

 

This gauge sounds like a great addon to my level-d 767, could you please provide me a copy?

 

Kind Regards,

 

Marcel

Hi Marcel

 

I most certainly can give you a copy, and as you probably know by now I have sent you a PM with the download link for the files and installation instructions.

 

As always, although you shouldn’t have any problems, but if you should then just let me know and I will try to help if I can.

 

Jim Hodkinson

Hello Jim,

 

Could you please send me the download link for the files and installation instructions ?

 

Thanks, aalper

I haven't sent a PM yet, but I had the gauge for FS2004 and it was a stress reliever. I don't know how many times I would try and hit shift + e + 1/2/3. I would either just open and close the main cabin door, or I'd end up bringing up the 2D panel. This is annoying with FSPassengers because it detracts points on your flight score if you open doors at improper times

 

I have also noticed that if I haven't properly started up the correct systems in the plane that I wouldn't get response from the cargo doors. After correct systems were started I would get a slightly better chance of getting the key command entered correctly.

 

Hodge001,

I've done a bit of upgrading on my PC with Windows8 and new hardware, so I'm taking the time to spring clean FSX. If it's not to much trouble, I'd like to send a PM for a link to download the cargo door gauge for the LevelD 767.

 

Thank you for sharing and patient with all the requests.

Hi aalper and niyoko

 

It is not a problem to send you the link for a copy of the gauge and installation instructions, in fact, and as you probably know by now I have sent you a PM with the download link for the files and installation instructions.

 

As always, although you shouldn’t have any problems, but if you should then just let me know and I will try to help if I can.

 

By the way I could never really get the hang of the key combinations either, hence the gaugeJim Hodkinson

 

P.S.

 

My apologies for the delay, but I had a bit of a system problem yesterday.

Hi Jim,

 

Can you please send me the link to your gauge.

 

Can you also tell me if ithe gauge uses key assignments for it's buttons as I would like to use real pushbuttons with the gauge via fsuipc if possible? This would be a great addition to the overhead in the cockpit I have made.

 

Regards

Mick

I'd appreciate a link to the gauge file as well. Thanks!

Hi Jim

 

It is not a problem, and as you probably know by now I have sent you a PM with the download link for the files and installation instructions.

 

As always, although you shouldn’t have any problems, but if you should then just let me know and I will try to help if I can.

 

@Mick

 

The gauge uses the standard (>K:TOGGLE_AIRCRAFT_EXIT) (>K:SELECT_1) command, obviously it uses (>K:SELECT_1) to (>K:SELECT_3) as well to be able to open all three exits, this command is basically the same as the Shift+E+1 to Shift+E+3 keyboard combinations.

 

Jim Hodkinson

Hi Jim

 

I have not received the download link, can you please send it again.

 

Thanks for the info about the commands.

 

Regards

Mick

Hi Mick

 

My apologies for that, I was certain that I had sent the PM, but I most certainly have this time, but let me know if there is a problem.

 

Jim Hodkinson

 

P.S.

 

This is odd as this post didn’t want to be posted either, the forum just sat there spinning it’s wheels with a saving post message, so with any luck it will post this time around.

Hi Jim

 

Thanks, got it this time and downloaded ok.

 

Yes, I had the same trouble with the saving post message with my last post.

It has also happened with this post so I refreshed the page like last time and hope it now works.

 

 

Regards

Mick