Title says it all.Just installed. Using the button version. Have set up my primary and secondary buttons fine. All loading ok except FSX will not load 2d panels as default. I have clicked and un-clicked the tick box in FSX but no dice.I can call up the 2d fine as soon as the cockpit appears, and I can see the FS2Crew bar when I hit the click-spot..Should I edit my FSX.cfg file and if so, where?Thanks in advancebestjakePlease ignore this post. A glance down the screen about four inches would have sorted me out :blush:bestjake

I have similar issue. NG loads in 2D but it stays in 2D for 2-3 seconds with MCP panel very blurred and then reverts back to VC. I do not know if it suppose to be like that or 2D should stay till I change it to VC. :(

Hi Ed,You have EZDOK I assume.Others solved it this way by changing their EZDOK setting:

Curious, in my case was the Edzok Camera Tool the mistake! After I set the tool to disable before I load the NGX in 2D and FS2Crew, I don't have any problem.

Thanks, BryanI thought I was going mad. I fixed it temporarily by deleting and recreating my fsx.cfg, but then everything (FSX, NGX, FS2Crew, textures, sounds!!) started to go pear-shaped, so I reverted to my original cfg and was just unable to get this to work - thanks for the EZDOK tip!bestjake

Hi Ed,You have EZDOK I assume.Others solved it this way by changing their EZDOK setting:

Oh. I have EZDOK. It pops up with NGX start. I'll try to change EZDOK then. Thank you.

Oh. I have EZDOK. It pops up with NGX start. I'll try to change EZDOK then. Thank you.

Hello back.I was following some advises from EZCA forum to disable EZCA on FSX start up and no luck. Does anybody know how to do that? I did the following and it did not help. It just removes EZCA completely. Open exe.xml file with notepad and rename "EZCA.EXE" to EZCA1.EXE or any name in this string: <Path>C:Program Files (x86)EZCAEZCA.exe</Path> For example: <Path>C:Program Files (x86)EZCAEZCA1.exe</Path> May be I did it a wrong way. Thanks.

Hi Ed,Does EZDOK have a support forum?I'd help, but I don't know the software well.Cheers,

Hi Ed,Does EZDOK have a support forum?I'd help, but I don't know the software well.Cheers,

Not much help from there so far. Will see. Thank you Bryan.

I also have EZCA.. so if I buy this product I'll have problem with no solution? I must admit I don't completely understand this thread.. why should I load 2d in the first place? Can't I just load in VC and than activate 2d panel? I'm seriously contemplating buying this but now I don't know..

I also have EZCA.. so if I buy this product I'll have problem with no solution? I must admit I don't completely understand this thread.. why should I load 2d in the first place? Can't I just load in VC and than activate 2d panel? I'm seriously contemplating buying this but now I don't know..

To ensure everything initializes properly.

Also note: You could probably get away with loading the VC first... FS2Crew is coded in such as way you should be able to.But to be safe, we recommend starting in the 2D.Also, remember after the 2D loads, you can easily switch to the VC.... just press the "A" key. Takes 1 second.Cheers,

But what exactly is the problem with EZCA and FS2CREW?

But what exactly is the problem with EZCA and FS2CREW?

There is none,..

That's right... there is none.People are just unsure how to get EZDOK to start in the 2D cockpit.But, codewise, you should be able to start in the VC.I only recommend starting in the 2D to be extra safe.

Thank you!