June 20, 201411 yr Hello, I was doing a flight from NZAA to KSFO and i noticed 20 minutes after takeoff my fmc is frozen i couldn't select any options or so! And my flight was at dusk and Night Sorry for my bad english
June 20, 201411 yr Hello, I was doing a flight from NZAA to KSFO and i noticed 20 minutes after takeoff my fmc is frozen i couldn't select any options or so! And my flight was at dusk and Night Sorry for my bad english Did you start with the cold and dark panel state? (it is broken) If you try another flight does the same thing happen? Also, read the PMDG forum rules RE signatures, they are about to crack down on unsigned posts etc. Wes Meyer
June 20, 201411 yr Commercial Member I was doing a flight from NZAA to KSFO and i noticed 20 minutes after takeoff my fmc is frozen i couldn't select any options or so! And my flight was at dusk and Night The screen may freeze if you cycle through your views and go past tower view when in the middle of the ocean, as you were. If that happens, press 'A' a few times when in the VC view, and it should sort itself out. Kyle Rodgers
June 20, 201411 yr Author I chose the "Short" Version on FMC and i did try using the views but nothing happened
June 20, 201411 yr I chose the "Short" Version on FMC and i did try using the views but nothing happened Is it just the FMS, everything else works fine? Do both main FMC's freeze? Wes Meyer
June 21, 201411 yr At the risk of asking a dumb question, what is the "Short" Version on FMC? Dan Downs KCRP
June 21, 201411 yr At the risk of asking a dumb question, what is the "Short" Version on FMC? I think he meant panel state "short turn" "long turn" etc. Wes Meyer
July 23, 201411 yr Hi guys ! I'm experiencing the same thing. Sometimes 15-20 minutes into the flight the FMC freezes. I am stuck on a certain page and cannot do anything. The strange thing is that the rest of the cockpit works. Normally that obligates me to shut down the flight and re-start it but sometimes I use the MCP to navigate to the runway. P.S: the 777 continues to follow the LNAV and VNAV path.
July 23, 201411 yr Hi guys ! I'm experiencing the same thing. Sometimes 15-20 minutes into the flight the FMC freezes. I am stuck on a certain page and cannot do anything. The strange thing is that the rest of the cockpit works. Normally that obligates me to shut down the flight and re-start it but sometimes I use the MCP to navigate to the runway. P.S: the 777 continues to follow the LNAV and VNAV path. Did you read the sticky at the very top of this forum. Pay to read it to be honest. System: MSFS2024, ASUS Rog Stryx Z790-A, Intel i9-14900KF, Asus ROG Ryujin III 360 , Asus Hyperion Case,Rog Stryx 4090 OC, Samsung 970 EVO M.2 SSD, 1Tb Samsung 860 EVO SSD,64Gb G Skill Memory, Asus Aura 1200W Gold PSU,Win 11 ,LG C4 48" 4K OLED Screen., Airbus TCA Full Kit, Stream Deck XL. WinWing FCU, EFIS, MCDU
August 12, 201411 yr Hi, I am having same issue with FMC freezing while flight plan input into FMC, especially while double clicking on "CG" and while punching data in Cost Index............... I have re-installed in PMDG-777 a couple of times but could not resolve the FMC freeze issue. Currently, just not able to fly of "CG" issue. Regards Rishabh
August 12, 201411 yr Hi, I am having same issue with FMC freezing while flight plan input into FMC, especially while double clicking on "CG" and while punching data in Cost Index............... I have re-installed in PMDG-777 a couple of times but could not resolve the FMC freeze issue. Currently, just not able to fly of "CG" issue. Regards Rishabh Have you tried in the VC clicking on the FMC and bringing up the 2D pop up ? and then test .See if that work using the 2D pop up.. If it does, it could be a dodgy video driver. System: MSFS2024, ASUS Rog Stryx Z790-A, Intel i9-14900KF, Asus ROG Ryujin III 360 , Asus Hyperion Case,Rog Stryx 4090 OC, Samsung 970 EVO M.2 SSD, 1Tb Samsung 860 EVO SSD,64Gb G Skill Memory, Asus Aura 1200W Gold PSU,Win 11 ,LG C4 48" 4K OLED Screen., Airbus TCA Full Kit, Stream Deck XL. WinWing FCU, EFIS, MCDU
August 12, 201411 yr Commercial Member Still not working........... Still not working...... Completely unhelpful. If you want help, be specific as to the issue you're having. If you're not going to help the person who posted the topic, don't post. Kyle Rodgers
August 13, 201411 yr Tried in the VC clicking on the FMC with 2D pop, still same issue freezes on entering data in "CG" CPU - I7-4790
Archived
This topic is now archived and is closed to further replies.