Jump to content

FSUIPC Forgets Key Assignments in P3D


Recommended Posts

Did you seek advice from the the FSUIPC support site?

 

 

I was hoping a wider user base had seen the issue. Truthfully, I find the support a little daunting. Pete tends to offer very complex support and I was hoping that there may just be  simple solution. If none can be found here I will try there. 

Mike Keigley

 

Boeing777_Banner_Pilot.jpg

 

Link to comment
  • Moderator

FSUIPC saves the general assignments in the fsuipc.ini file. After you set it, exit and check the ini file. If it's there, fly etc until it fails. Exit and look at the ini file - if it's there, your problem is either RC or P3D - I'd think RC or something is also using that key mapping.

 

 

Vic

 

RIG#1 - 7700K 5.0g ROG X270F 3600 15-15-15 - EVGA RTX 3090 1000W PSU 1- 850G EVO SSD, 2-256G OCZ SSD, 1TB,HAF942-H100 Water W1064Pro
40" 4K Monitor 3840x2160 - AS16, ASCA, GEP3D, UTX, Toposim, ORBX Regions, TrackIR
RIG#2 - 3770K 4.7g Asus Z77 1600 7-8-7 GTX1080ti DH14 850W 2-1TB WD HDD,1tb VRap, Armor+ W10 Pro 2 - HannsG 28" Monitors
 

Link to comment

I am now seeing another issue I have not seen before. P3D is no longer allowing me to Alt-Enter out of the full screen. I wonder if this is related. I have to press alt and then choose alt-enter from the menu. Strange. I may just use the work around until the next version comes out. 

Mike Keigley

 

Boeing777_Banner_Pilot.jpg

 

Link to comment

I am now seeing another issue I have not seen before. P3D is no longer allowing me to Alt-Enter out of the full screen. I wonder if this is related. I have to press alt and then choose alt-enter from the menu. Strange. I may just use the work around until the next version comes out. 

 

I have an issue with blurries that have suddenly popped up, and I have tried everything except a reinstall of P3D. I am like you, hoping that it won't be long before the new version is available. Wish they would give us some approximate time frame for that to happen. 

spacer.png

BOBSK8             MSFS 2020  PMDG 777    ,PMDG 737-600-800 Fenix A320, FSLTL , TrackIR ,  Avliasoft EFB2  ,  Beyond  ATC  , Flightsim First  Officer A320,777

A Pilots LIfe V2 ,  CLX PC , Auto FPS, ACTIVE Sky FS,  PMDG DC6 , A2A Comanche, , Milviz C 310

 

 

Link to comment

I have an issue with blurries that have suddenly popped up, and I have tried everything except a reinstall of P3D. I am like you, hoping that it won't be long before the new version is available. Wish they would give us some approximate time frame for that to happen. 

 

Plus it will probably be a while before all of our "must have" addons are updated to work with the new version. Which means  being stuck with these issues for awhile. 

Mike Keigley

 

Boeing777_Banner_Pilot.jpg

 

Link to comment

Now things are getting even weirder. On a PANC-VHHH flight half way through I went  to adjust the time that FSUIPC autosaves and the FSUIPC tab is missing from the menu. Maybe I should delete my configuration file and build a new one. The autosave has been cussing very long pauses upon every save. It did not do this before and all this has surfaced in the last couple of weeks. Not to mention that GSX has stopped working as well. î

Mike Keigley

 

Boeing777_Banner_Pilot.jpg

 

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...