Jump to content

Sign in to follow this  
RodgerC

Elevator Problem

Recommended Posts

Immediately after the latest update, all airplanes that I have flown have a severe elevator spiking problem.  At the least bit of backpressure the yoke in the simulator starts to spike 5*-10* degrees.  I've never experienced this problem before.  Landing can be a nightmare trying to get the airplane on the ground.  I have had the sensitivity set perfectly ever since the sim came out.  I've played with the sensitivity but it does nothing for the "spike" in the elevator.  Tried restarting the simulator, rebooting my computer.  Nothing that I have tried has helped.  Anyone have any ideas???  Thanks

Share this post


Link to post
Share on other sites

Calibrate it in Windows and if the problem persists then experiment with your Dead Zones.

That's all I can think of at the moment as nothing in my Controller Settings seems to have been touched by the Update.


Intel Devil's Canyon 4790K@4.6, EVGA 1080 Ti Gaming OC, 16 GB 2300Mhz and a bunch of SSD's to run it all. And wings.

Share this post


Link to post
Share on other sites

Now I have tried 4 times to get into MSFS 2020 and it has crashed 4 times in a row.   Frustrating.  The other day I had a total of 11 crashes in a row........  So tired of it taking a week to get the update straightened out then as soon as you get the sim running again to your liking here comes another update to take all the work away and start all over again....

Share this post


Link to post
Share on other sites

Since the update I have had the Baron G58 'jump' vertically off the runway at around 130 kts & T/Off flap.

Jumps about 10' in the air & keeps flying.

Didn't do it when I tried zero flap.

T45

Share this post


Link to post
Share on other sites

Not sure if this is still pertinent after the France/BeNeLux update but it might help.


-Jay

9700K | RTX 2080Ti @ 4K | 48GB DDR4 | 2 x 1TB SSDs | RC Cola

Share this post


Link to post
Share on other sites
1 hour ago, RodgerC said:

Immediately after the latest update, all airplanes that I have flown have a severe elevator spiking problem.  At the least bit of backpressure the yoke in the simulator starts to spike 5*-10* degrees.  I've never experienced this problem before.  Landing can be a nightmare trying to get the airplane on the ground.  I have had the sensitivity set perfectly ever since the sim came out.  I've played with the sensitivity but it does nothing for the "spike" in the elevator.  Tried restarting the simulator, rebooting my computer.  Nothing that I have tried has helped.  Anyone have any ideas???  Thanks

Somehow after last update somehow my saved  binding  profile got reshuffled. I would check if any binding sensitivity and curved go reset


flight sim addict, airplane owner, CFI

Share this post


Link to post
Share on other sites
4 hours ago, sd_flyer said:

Somehow after last update somehow my saved  binding  profile got reshuffled. I would check if any binding sensitivity and curved go reset

I checked it and it was still the same...

Share this post


Link to post
Share on other sites
5 hours ago, Twenty6 said:

Not sure if this is still pertinent after the France/BeNeLux update but it might help.

That was the first video I watched after this started.  But still can't get the problem solved.

Share this post


Link to post
Share on other sites
10 hours ago, RodgerC said:

That was the first video I watched after this started.  But still can't get the problem solved.

I also removed any and all calibration from FSUIPC7.ini which helped, especially with the Carenado Mooney.


-Jay

9700K | RTX 2080Ti @ 4K | 48GB DDR4 | 2 x 1TB SSDs | RC Cola

Share this post


Link to post
Share on other sites

Just throwing this out there... Has your "Flight Model" changed from "Modern" to "Legacy" in settings?

Some updates have been known to change that setting on some systems.

...jim

 

Share this post


Link to post
Share on other sites
1 hour ago, JimBrown said:

Just throwing this out there... Has your "Flight Model" changed from "Modern" to "Legacy" in settings?

Some updates have been known to change that setting on some systems.

...jim

 

I'll have to check that.  But now I have a bigger problem.  4 consecutive CTD's.  I can't even get it to open up, let alone check anything.  Thanks, I'll check it out whenever I can actually get the program to work.

Share this post


Link to post
Share on other sites
2 hours ago, Twenty6 said:

I also removed any and all calibration from FSUIPC7.ini which helped, especially with the Carenado Mooney.

I don't have any FSUIPC7 calibrations.  All done thru the sim..

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    47%
    $11,800.00 of $25,000.00 Donate Now
×
×
  • Create New...