June 7, 20205 yr Recently I am keep getting this message from P3D: "P3D has detected non-sequential layer ordering within the Scenery Library list. Would you like P3D to attempt to repair this issue? YES or NO I usually click YES. Then every time when I start P3D, it starts all over again. How shall I correct this issue?🤔 Thanks Edited June 7, 20205 yr by asanal Ahmet Sanal "Time you enjoyed wasting, was not wasted"
June 7, 20205 yr 12 minutes ago, asanal said: Recently I am keep getting this message from P3D: "P3D has detected non-sequential layer ordering within the Scenery Library list. Would you like P3D to attempt to repair this issue? YES or NO I usually click YES. Then every time when I start P3D, it starts all over again. How shall I correct this issue?🤔 Thanks What sceneries you have? ORBX? Did you tried P4AO from Lorby? Finds all issues, duplicates and puts them in order..... Alex
June 7, 20205 yr Author I have ORBX. Sorry to say I have no knowledge about Lorby. I will search and will inform. THX Ahmet Sanal "Time you enjoyed wasting, was not wasted"
June 7, 20205 yr 1 hour ago, asanal said: Recently I am keep getting this message from P3D: "P3D has detected non-sequential layer ordering within the Scenery Library list. Would you like P3D to attempt to repair this issue? YES or NO I usually click YES. Then every time when I start P3D, it starts all over again. How shall I correct this issue?🤔 Thanks I believe its related to the layer priorities in the scenery.cfg which as you may know are numbered by layer 1....20...200 whatever. When one moves a layer inside the sim, the layers get renumbered to be linear. However here are circumstances such as manual adjustment where layer say 49 will get moved before 48 and this triggers the message. Or a scenery is deleted and leave a gap in numbers. Make a backup copy of your scenery.cfg....then let the sim adjust check to see if everything is displaying properly. You can scan through your scenery.cfg and see if the numbers are all sequential. You may find the culprit. Bryan Bryan Wallis aka "fltsimguy" Maple Bay, British Columbia Near CAM3
June 7, 20205 yr Author Brayn, Thanks. I made a backup copy and delete the scenery.cfg and let sim redownloaded Scenery.cfg and at tis time no warning received from P3D. RWY24, I found Lorby web site, but I cannot locate P4AO. In mean time problem solved, Thanks for your help. Ahmet Sanal "Time you enjoyed wasting, was not wasted"
June 7, 20205 yr Commercial Member 44 minutes ago, asanal said: P4AO Just look for Prepared Add-on Organizer. It's not only one of the best tools for P3D users, the documentation is a MUST READ for P3D users and doing so will save you many, many hours - trust me on this, I do this and flight sim support professionally. You may not understand everything in the documentation the first time, but it will give you a terrific foundation and you'll know where to go for help should you need it in the future. Recommending you make the time to read the documentation is easily the best flight sim related advice I can give you my friend, especially since most P3D Addons (aircraft, scenery, and all other addons) now use the XML method for adding and activating/deactivating P3D addons. Best wishes! Dave Hodges System Specs: I9-13900KF, NVIDIA 4070TI, Quest 3, Multiple Displays, Lots of TERRIFIC friends, 3 cats, and a wonderfully stubborn wife.
June 7, 20205 yr Even with addin organizer the message will come back. I get it all the time, run Lor y and it goes away fir a bit then comes back. Mark CYYZ
June 7, 20205 yr 36 minutes ago, MarkW said: Even with addin organizer the message will come back. I get it all the time, run Lor y and it goes away fir a bit then comes back. This might indicate that perhaps ORBX Central introduces it, every time you run it for (re-)installing a scenery or other management tasks. I still don't really understand the layering ORBX (+P3D5) introduces via add-on.xml installations. But of course there may be other causes. Kind regards, Michael Intel i7-13700K / AsRock Z790 / Crucial 32 GB DDR 5 / ASUS RTX 4080OC 16GB / BeQuiet ATX 1000W / WD m.2 NVMe 2TB (System) / WD m.2 NVMe 4 TB (MSFS) / WD HDD 10 TB / XTOP+Saitek hardware panel / LG 34UM95 3440 x 1440 / HP Reverb 1 (2160x2160 per eye) / Win 11
June 7, 20205 yr Moderator Try adjusting your insertion point in Central and then sync to sim. Vic RIG#1 - I9 14900K MSI Pro z790 RTX 5070Ti 40" 4K Monitor 3840x2160
June 8, 20205 yr Author Thanks all responses And advises👍. I deleted Scenery. cfg file and started P3D and generated the new Scenery.cfg file. There are no more P3D messages. Also, " ORBIX Central" I clicked "Verify Files" on Orbx Libraries" folder. Ahmet Sanal "Time you enjoyed wasting, was not wasted"
June 8, 20205 yr 11 hours ago, MarkW said: Even with addin organizer the message will come back. I get it all the time, run Lor y and it goes away fir a bit then comes back. Just opening C4 will check your installed scenery and reorder it if you have not set the insertion point correctly, even if you do not add or make a purchase it needs to know what you have installed already. PS that`s how it checks to see if you need updates on some scenery. Edited June 8, 20205 yr by G-RFRY Raymond Fry.
June 8, 20205 yr I open Orbx Central 4 all the time to check for updates and recently to add Vector. Mark CYYZ
Archived
This topic is now archived and is closed to further replies.