I was wondering if we could get a list going of airports with mesh issues on the runway. There's nothing worse than flying hours on end only to crash during rollout because the runway is broken like an Earthquake hit it.

I'd love to see a proper list, so I know what airports to avoid right now.

Must be lucky i have yet to come across a runway that's that bad it wrecks your aircraft. I have seen some bumps in newly released addons, but these are usually fixed by the devs pretty quick.

The only broken runway I’ve come across so far was the result of having two versions of the same airport active.

30 minutes ago, Car147 said:

Must be lucky i have yet to come across a runway that's that bad it wrecks your aircraft. I have seen some bumps in newly released addons, but these are usually fixed by the devs pretty quick.

 

27 minutes ago, Gate99 said:

The only broken runway I’ve come across so far was the result of having two versions of the same airport active.

I have a clean install (Completed an hour ago) on a new SSD. KTPA had a tear on every runway, so I came here to see if a list could be compiled.

1 hour ago, WestAir said:

 

I have a clean install (Completed an hour ago) on a new SSD. KTPA had a tear on every runway, so I came here to see if a list could be compiled.

Hi WestAir,

                     Out of curiosity I just tried taxing down the full length of  runway 19L and 10. I did see any runways problems and the plane taxied smoothly. Any chance that you have a freeware/payware version of the airport that's creating a conflict?

 

All default. I'm curious if maybe it's a certain graphics setting that causes the discrepancy. I might have to sit in front of a tear and then raise / lower settings to see if I can make them disappear.

There are plenty of them around. Adobo/MS should take care of them

https://forums.flightsimulator.com/t/runway-tears-awareness/314575/25

 

LFRN Rennes airport in brittany France has this problem when landing.

Patrice

 

32 minutes ago, WestAir said:

All default. I'm curious if maybe it's a certain graphics setting that causes the discrepancy. I might have to sit in front of a tear and then raise / lower settings to see if I can make them disappear.

Perhaps it is. Good luck with it

KPDX

KSEA

there are a ton of these in the pacific northwest.  I am almost sure it has to do the PC ability to handle the load.  If I fly in with a low speed aircraft (ie caravan or less) no issue, however with any of the jets, you will flip on the runway at multiple locations.  I have tested this by bringing all of my settings to the lowest and there were not problems, once I start taxing my system, that is when this starts occuring.

9 hours ago, WestAir said:

I'd love to see a proper list, so I know what airports to avoid right now.

 

Well, where is your list? Since you flagges this as a problem, I'm assuming you have a few airports in mind?

Seems there is a problem when landing on Navy airport KNTO Oceana Va. When landing on 23L and trying to turn off to taxiway A after rollout, there is a large invisible wall. Have tried a number of planes which get bounced/blocked. Does not seen to exist at other points along 23L.

It seems that those runway anomalies can occur at every airport that is located in a photogrammetry area. I personally came across this glitch at KSEA, KJFK and LIRQ. 

LIRQ is one of those, I can't keep crash detection on at this state, it would only add to the frustration.

On 11/16/2020 at 10:25 AM, EmaRacing said:

LIRQ is one of those, I can't keep crash detection on at this state, it would only add to the frustration.

I've never used crash detection in 40+ years of flight simming. What's the point? I just say "gee-willickers, I crashed". And continue on.