prdant

Thank you for the information, I will check it out once I get home.

So I purchased this aircraft today. I have searched the files for an user guide but I cannot locate the guide. I can't figure out how to load fuel. I know that this sounds lame but this is my first Carenado purchase. Any help will be appreciated. Thanks .

Sorry to reply late but it seems that I needed not only the 2105 version but redistributable 2010 and 2013. All's well in 777 land now.

Thanks for the great tips. I will dig into it further.

Any help will be appreciated. My 777 Worldliner Professional works great on my Surface and until tonight on my PC. Earlier today when loading it up it throws a warning regarding an overspeed and the FMC will not start. I found a thread stating that I should add JAVA, which I did. Now loading the 777 shuts down X-Plane, I will try to remove the latest JAVA but I wonder if anyone has a thought on if this will work or has had a similar issue. Thanks in advance.

The search begins!!! Thanks, at one point I was a voice on RC so maybe JD still remembers me.

Can anyone tell where to purchase again? When I get home I will check my E drive to see if it may still be there if not I will need to reorder.

Thank you very much

Thank you sir

All, any idea who to contact about not getting a permanent key for World Traffic. Purchased and downloaded over the weekend but still no key. Tks in advance

All, please forgive my ignorance. I have been away from simming for awhile. Does RC4 work with xplane and is it still available.

I am not near my PC now but you have to use panel loadstate to get to load that way. Not sure of the exact wording on the FMC. It is in the introduction manual; 4) STARTUP PANEL STATE: This prompt allows you select a saved panel state that you would like the simulation to use as your default panel condition every time the simulation is launched. For example, if you were to select a Cold and Dark scenario as the STARTUP STATE for the airplane, you will be presented with that cold and dark panel state whenever and wherever you choose the load the NGX

I too have run into this, I have FSUIPC but have not seen the zapper. Can you explain? Thanks

Thanks Damien

If I manually tune the radios or altitutes etc, does that then stop FS2C from working? In other words can I manually tune once and then ask the F/O to do it the next time without messing up FS2C? Thanks

Sorry about that, here is a good free site: https://www.notams.faa.gov/dinsQueryWeb/

North Atlantic ABC/North Atlantic Tracks and valid altitudes on-line between 2300-0100z, valid 1130-1900z. XYZ/North Atlantic Tracks and valid altitudes on-line between 1200-1400z, valid 0100-0800z.

I checked with one of our dispatchers and he said that the NAT tracks are more often used for flights that go further into Canada or the US. He was not sure if ATC would give you a direct segment off of the track. Below is the routing we got, not flying the tracks: EGSS BUZA7R BUZAD T420 WELIN UT420 TNT UL28 PENIL UL70 BAGSO.. DOGAL..5420N..5330N..5140N..4850N..NOVEP..CYYT

There is a good youtube video on how to reduce the shaking and pilot head movements. I think there are three in this series;

On my Saitek quadrant I get reverse power by going to the button tab in fusipc, moved the throttle past the detent to the bottom, then set that as F2 check to hold as long as depressed, then F1 when released. Sorry for not being the exact words but I am not at the PC. However now when I pulled throttle all the way down the reverser come on until I move the throttle back above the detent.

How many of the task are you using the FO for versus the Captain. For example are you using the FO to change altitudes or frequency during the cruise segment? During the initial setup? etc etc.

I show "Securing Aircraft Checklist" as the command. But then again I am new to this.

Thank you very much

Is there a way to key the main panel open while switching views. After starting the PF I go to the overhead an allign the IRS but going back to the main view I have to click open the main panel and then config again. Sorry if this has been asked nbefore but I don't see it in the search

Not so far, but I am just getting started.