Jump to content

Archived

This topic is now archived and is closed to further replies.

HiFly

Suggestion for SP2

Recommended Posts

Every gauge on the overhead has a tooltip so you can read the tiny displays EXCEPT the cabin altitude and PSI. It would be nice to include a tooltip for this and also the Climb Rate dial so they can be read without having to enlarge the overhead VC camera view by at least 4X each time they are checked.


Craig Williams

Share this post


Link to post
Share on other sites

It would also be great if the stabiliser trim setting pop-up appeared more reliably - and updated more immediately as you wound the wheel- to save having to zoom in to check the setting. Sometimes you have to run the mouse over the wheel several times before the box appears ...

 

Small point, I know ...

 

Best wishes,

 

David


David Abrahams

 

800driver.jpg

Share this post


Link to post
Share on other sites

As far as I can tell that is FS thing, not PMDG thing.


--Peter Fabian 
RTFM.jpg

Share this post


Link to post
Share on other sites

It does appear immediately, you need to place the cursor on the trim wheel where the speedbrake is, in the retract position.


Fareed

737NG%20Banner%20AVSIM.jpg

Share this post


Link to post
Share on other sites

Another thought for SP2:

 

Could we possibly have an option to pause the sim (say) 50NM before ToD, so that we can get the pre-descent flows and checklist done in good time?

 

Especially with the added realism and operational discipline introduced by FS2Crew, completing the descent flows and checklist way before time, so you can go downstairs for a coffee feels like cheating - but then trying to do it all in 10 seconds flat when you un-pause is a bit of challenge too!

 

Best wishes,

 

David


David Abrahams

 

800driver.jpg

Share this post


Link to post
Share on other sites

David, if you have it, Radar Contact has a "pause at [distance]" option, where you set the distance to suit. Very handy.

 

Paul Scholey


Paul Skol

Share this post


Link to post
Share on other sites

Thanks for that, Paul. Yes, very handy indeed. Have definitely been thinking of Radar Contact, but not until my system's a bit punchier!

 

Best wishes,

 

David


David Abrahams

 

800driver.jpg

Share this post


Link to post
Share on other sites

I have also anidea for SP2.

 

When fill or adjust the fuel via the manager the ctr pumps goes on. But in the pre-flight when i do the payload ect i dont need the pumps.

 

Another thing is the 2d panel. After serval years using the 2d im completly turn over to the vc. It would be nice you can deactivate or remove the 2d panel. When use the "a" to cycle the views i won't see the 2d.

 

Thanks PMDG and hurry up for 777 ;)


Remco

Share this post


Link to post
Share on other sites

+1 for x distance from TOD pause. I'd like to have an option to enter a distance in there.


Regards,

Bob Quick
 

Share this post


Link to post
Share on other sites

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    28%
    $7,075.00 of $25,000.00 Donate Now
×
×
  • Create New...