-
Content Count
1,330 -
Donations
$20.00 -
Joined
-
Last visited
Content Type
Profiles
Forums
AVSIM
Media Demo
Downloads
Gallery
Blogs
Forms
Everything posted by asanal
-
During the decent A/P disconnects with out any reason. This is happening during flights with 777. Today's flight from KEWR to KDEN was perfect ,but when started to decent from FL380, at FL340 A/P disconnected the plane sharply begin to dive. I recovered. At FL270 again disconnected and dive the plane and I recovered. Final one when I reached to FL150 same problem, A/P disconnected and nose dive to 9000 Ft I recovered again and landed with out any problem. What should I check, to identity "Why" it is happening.
-
Problem solved.Thanks again.
-
Bill, Thanks. I will do it.
-
I am receiving the following warning when ever I open P3D loading screen. How can I solve this problem?
-
Klaus, Thank you
-
For Once And For All...who wants to pay for a new PMDG MD-11?
asanal replied to rheinis's topic in PMDG General Forum
Don' give up, YES -
Prepar3D Tweak Assistant (PTA)
asanal replied to KNOSSOS's topic in P3D Tweak Assistant (PTA) and RealismShaderPack
MIke, Finally I succeeded. Thanks to you. -
Prepar3D Tweak Assistant (PTA)
asanal replied to KNOSSOS's topic in P3D Tweak Assistant (PTA) and RealismShaderPack
Mike, Thank you writing the instruction. I will start to work on it. It will not be easy for me. It will take time. -
Prepar3D Tweak Assistant (PTA)
asanal replied to KNOSSOS's topic in P3D Tweak Assistant (PTA) and RealismShaderPack
Mike, Hi How do you install Adam' s preset. I purchased Matt PTA downloaded/installed, but I don't know how to change New Preset. Thanks -
wrong post.
-
OK,,It is a good news
-
http://www.prepar3d.com/forum/viewtopic.php?f=6313&t=122277
-
When I clicked on "Print Screen" key, I have to go "Irfan View 64" software" to capture the picture. Do you have "Irfan View 64" ?
-
Did you tried "Print Screen" Key ?
-
Drzewiecki Design - New York Airports v2 released
asanal replied to Drumcode's topic in The Prepar3d Forum
Some thing going wrong with DD installation. It is taking to much time ( 6+ minutes) to load P3D. How can I uninstall DD ? -
Drzewiecki Design - New York Airports v2 released
asanal replied to Drumcode's topic in The Prepar3d Forum
Jim , Milton, Thanks for your responses. -
Drzewiecki Design - New York Airports v2 released
asanal replied to Drumcode's topic in The Prepar3d Forum
Any help for remaining above two questions. -
Drzewiecki Design - New York Airports v2 released
asanal replied to Drumcode's topic in The Prepar3d Forum
Orman, Thanks -
Drzewiecki Design - New York Airports v2 released
asanal replied to Drumcode's topic in The Prepar3d Forum
I just purchased and installed two part DD . All airports look great. I have three questions? 1- How to move Jetway ? Ctrl+J doesn't work. 2- "Stand not available" What does it mean? 3- PFPX no longer load Flight Plan (PMDG 777/747) Does DD in influence PFPX ? Thanks -
AI Traffic and good ATC recommendations needed for P3Dv4
asanal replied to cowboy10uk's topic in The Prepar3d Forum
I utilize Radar Contact with out any incident in P3D v4. I am very satisfied and recommend RC4 as ATC service provider. -
Unfortunately I have CH yokes
-
JaeCheol, Is your response for my " "Tire Blowup and break heat " failure ?
-
Kyle, You are right. Today's flight it happened again. I cleared from " Failure" in FMC . As you advised ,I have to fix the calibration issue . I don't thing I can do it. It will be better , if I open a "Support Ticket".
-
I suggest open the FMC and check the "Failure"" settings . You will find "Tire Blowup and break heat " failure already programmed for you. Clear them. You will not experience again.
-
Kyle. Thanks for your help. I did followup your instruction, but result was same. I re-installed DC-6 P3Dv4. Documents and manuals are appeared in PMDG Operating Center. Problem solved