Skip to content
View in the app

A better way to browse. Learn more.

The AVSIM Community

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

yosss

Members
  • Joined

  • Last visited

  1. The Twin Commanders will definitely be a day-one purchase for me. You can't go wrong with Black Square!
  2. Following the recent update to the TBM, Blacksquare has now updated the Caravan Professional to version 0.1.3. I'll paste the changelog below: v1.3 - Full State Saving and More Variables for Hardware Control - 2026/11/11 New Features: Completely new full state saving system with 280 parameters, using JavaScript state saving, rather than state.cfg. See the “Full State Saving” section of this manual for more information on the system, and the “Options Page” section for configuration options. Added disabled visual state to tablet options switches (greyed out), like engine/pitot covers/chocks to provide feedback when these options are not available. Added new gauge glass material for MSFS 2024 to introduce more cubemapped reflections while preserving most surface imperfections. This hopefully strikes a good balance for users who miss the more vibrant reflections of MSFS 2020, and those who find MSFS 2024’s reflections too distracting. Added clickspots to enter/exit the aircraft in MSFS 2024. When the pilot’s door or cabin doors are open, click on the ground to exit the aircraft. From the exterior, click on the pilot’s seat or the floor of the cabin to enter the aircraft. Added custom oil pressure simulation, in which viscosity influences oil pressure. Added custom external power system, which bypasses the parking spot limitations of MSFS, and avoids random disconnects. External power can now be enabled anywhere. Added inertial separator influence in ITT calculation. Added standby alternator controller battery power connection. The annunciator panel will now remain illuminated after complete electrical shutdown, which can serve as a reminder to toggle the standby alternator switch to the off position. Slightly improved aft-facing propeller disk material in MSFS 2024 (when propeller is spinning) for more subtle effect with less stroboscopic behavior. Added temperature dependent CRT warmup effect to weather radar screen. Added differential inertia constants to flight model for MSFS 2024 to compensate for perceived increased control sensitivity compared to MSFS 2020. The KAP140’s barometer unit (toggled by holding down the “BARO” button) will now be saved between flights. The generator switch will now respond visually to “L:var_GeneratorSwitch” changes. The remote compass manual rotation switch will now respond visually to “L:var_GyroSlaveDirectionSwitch” changes. The inertial separator handle will now respond visually to “L:XMLVAR_InterSep” changes. When the ignition switch is in the on position, an interlock circuit will now prevent the starter from energizing when the starter switch is placed in the “MOTOR” position. Added a variables for cockpit builders to easily trigger the momentary deicing switches to their manual positions: “L:var_WindshieldDeiceSwitchOverride”, “L:var_PropDeiceSwitchOverride”, and “L:var_AirframeDeiceSwitchOverride”. Added additional variable setting on startup to compensate for confused loading sequence in MSFS 2024, which frequently resulted in engine parameters, equipment temperatures, and cabin environmental variables being populated with ambient temperatures from deep space. Pressing the door toggle buttons on the tablet’s payload screen will now stow the ladder if it is blocking the door. Pressing the button again will subsequently close the door. Bug Fixes: Finally found the cause of erroneous nose gear touchdown chirping while taxiing and rolling down the runway. Fixed L:Var var_trueAirspeedRing not animating the true airspeed calculator ring, despite setting the underlying variable, and adjusted the rotation speed for legacy interaction mode. Reversed direction of remote compass rotation switch and synchroscope to match description in the manual, and reduced speed of manual adjustment for more precise compass setting. Fixed the airframe deicing switch manual position not triggering boot inflation in some circumstances. Fixed “starter controller” on the live schematic not illuminating with starter bus external power only. Fixed starter switch and signal on the live schematic flickering when the starter automatically cuts out after the engine becomes self-sustaining. Starter signal may have illuminated when external power was connected, but not online. Fixed implementation issue with engine-driven fuel pump failure that resulted in no torque, despite positive fuel pressure from electric pumps. Fixed navigation lights not dimming with battery voltage like other exterior lights. The outside air temperature probe/gauge was missing glass-tap sound. Fixed missing PMS50 GTN 750/650 knob pushing animation in all aircraft after Dukes. Added missing “PUSH CRSR” integrated lighting on GNS 430. Fixed placement of light stem emissive mesh on right side of pilot’s airspeed indicator. Dynamic registrations on the left side of the aircraft were only medium weight fonts, instead of bold, due to a misplaced curly bracket. Removed “Cloud Strobe Effect” from tablet options list, as the effect will now be permanently enabled. (The effect is not as severe as I had once worried, and I have never received any complaints about it.)
  3. The Echo 19 sound pack has been updated. Just re-run the installer and version 1.0.0.1 can be downloaded. Installing now..
  4. This tool works really well. As far as I can tell, it has no impact on performance whatsoever. It really makes the aircraft feel much more alive.
  5. I am really impressed with this one — a wonderful aircraft that flies great. However, I cannot get crossfill to work when using the TDS GTN 650/750. I’ve only tried the pressurized Baron so far, not sure if it’s just on my end. EDIT: Surely works after restarting the flight 🙂
  6. The flickering is gone at my end. Only tested for a few minutes.
  7. Thank you for sharing this. Yes, i am running DX12 due to frame generation. It would of course be nice to see this problem addressed. I guess we're lucky this problem only arises at some specific airports. I will monitor this problem and report back if I come across some sort of solution.
  8. I also have this issue at Aerosoft ENGM. Not sure what is causing it. Are you using REX AccuSeason?
  9. I can confirm that you can turn off the transition effect. Works very well!
  10. Fsreborn FSR500 seems to work without any major problems. My only issue is that the tablet sometimes is a bit unresponsive to mouseclicks. However, when I position the camera right in front of it it's working as it should. I tried the Blacksquare TBM 850 but no engine sound. The switches also did not make any sound. Testing a few more..
  11. After you bind new keys for saving and loading custom cameras, restart the sim. This worked for me!
  12. Make sure you have set "global texture resolution" to high in the main display settings page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.