loonyknownothing

Hi everyone. Www.wegoairwaysva.co.uk is pleased to announce we have completed the summer schedule and fleet updates for our 158 airlines!!! We have also added 6 new airlines to the WeGo World Alliance. Come on over and have a look around. feel free to ask any questions kind regards Mark Callison

I too use an average of 25% N1 during taxi pre flight, about 27% to get rolling and 23-24% post flight.

Update. I created a support ticket as i wasn't getting anywhere and turns out it is a fault and has been put forward to the development team.

I've never been able to enter a step climb that way on the NGX. I always get a invalid entry warning. I've always done it that way on the T7 & 744. I'll dig into it more and read the FCOM properly. Thanks for your assistance everyone.

Basically my VA flight tracker will detect if I fly over 250kts under FL100. So i like to set a Speed restriction to 240 under FL100 so as to save my tracker from detecting the "overspeed" I have always done it this way. As as per the FCOM 11.41.3 (I just read it (i won't lie i hadn't before now)) it does say manual entries maybe added. So I would basically in LSK3L enter 240/100 and that would prevent my aircraft flying above 240kts below FL100. This would be over ruled by and SID restrictions where speeds would be slower. Then when above FL100 the plane would auto climb under VNAV to the selected speed and altitude. Now if I enter a step climb in the crz page whilst on the ground then my entry will be removed, unable to add any entry and then whilst climbing out on any unrestricted SID the plane will just shoot to cruise speed in the climb from takeoff. If i don't enter a step climb or enter it after FL100 then it works how it always used to I really hope this makes sense.

ok so it appewars to be if i preselect a step climb in the crz page its will delete any entry into the spd rest point on the clb page.....

nope, completely removed all traces of V3 before installing V4. Including scenery and aircraft. It also doesn't matter if its cld&drk or engine ready. I've noticed I can enter the restriction when on the ground but once taken off it just removes itself

Morning all, I have noticed that I am unable to manually enter speed restrictions in the climb page. Just get a invalid entry warning message. I type it as 240/10000 or 240/100, same message when trying to enter in the "SPD/REST" SECTION. Also noticed it will not auto stick to 250 below 10000ft. Just speeds to cruise speed. Can enter a speed restriction into the legs page for a certain way point and it will adhere. Been a few months since I've flown this girl but i'm sure that is what I used to do!! http://prntscr.com/fvz4lk Any help would be greatly appreciated Thanks

I'm afraid not.......my 5 year old still constantly asks why?? oops sorry........just noticed this was an old post........my bad

Hello there, We at WeGo Airways Virtual are starting a recruitment drive. We want to hear from you to see what you look for in a virtual airline. Be it Real world operations, the flight tracker or a teamspeak atmosphere. Come take a look at us at www.wegoairwaysva.co.uk. We have been operating since February 2015 and have been operating steadily since. We have 56 real world airlines with full schedules and fleets updated regularly. We also have our own Charter division with our own livery for a variety of aircraft and also a cargo division. Our own fleet consists or a variety of aircraft from Cessna aircraft up to A380 & B774/778 With our real world airlines we have the globe covered no matter where you like to fly. We are not a very strict VA. You may fly overnight whilst you sleep if you wish. You may also pause a flight at TOD so you can go watch the football or (let) your partner take you out shopping!!! We use kACARS as our tracker and update it regularly with new features. We also support X-Plane 10 & 11, P3D V2 - P3D V4 and FSX FSX-SE Pop on over and take a look or leave us a comment on here with any questions you may have. Best Regards Mark Callison VCEO WeGo Airways Virtual

Hi, I couldn't connect to Ifly 747 V2 and found out there was an update to the Interface. Downloaded the interface update 2.22.1.11622 and installed as admin. Run it as admin but when I hit connect on the iPad it just says connecting until it times out. I have checked the I.P address and the port is on default 9000. And restarted the iPad app. It was working fine for the NGX 2days ago! If i go to the control panel it registers the correct aircraft and that its P3D. I'm not sure where else to go

would a thermo camera not help for cargo? there seems to be alot of cargo smoke detector failures. If you could check a thermo camera surely then you could decide to divert or carry on? or at least get to your nearest maintenance. probably save alot of money??

Hi Keven, No worries. I think it is working even though SE doesn't illuminate. I have just been through some pretty cloudy stuff and landing lights looked beautiful!! Guess I just wasn't in the right weather. I will check some snow n rainy weather later and report back. In hind sight I probably should of checked this first. Thanks for your assistance, Mark Callison

Morning, I appreiciate its the holidays but is there any update on this?? If not no worries. Just making sure it hasn't been missed :-) HAPPY HOLIDAYS

Evening Keven HKEY_LOCAL_MACHINE\Software\Wow6432Node\Microsoft\Microsoft Games\Flight Simulator\10.0 Key: SetupPath C:\Program Files (x86)\Steam\steamapps\common\FSX HKEY_LOCAL_MACHINE\Software\Wow6432Node\DovetailGames\FSX Key: Install_Path C:\Program Files (x86)\Steam\steamapps\common\FSX HKEY_LOCAL_MACHINE\Software\Wow6432Node\Lockheed Martin\Prepar3D v2 Key: SetupPath NO PATH (DON'T HAVE V2 THOUGH?) HKEY_LOCAL_MACHINE\Software\Wow6432Node\Lockheed Martin\Prepar3D v3 Key: SetupPath C:\Program Files (x86)\Lockheed Martin\Prepar3D v3\ Hope that is correct :/ not 100% sure what i'm doing Many thanks again Mark