does anyone else have problems with this Swiss Mesh in Zurich City environs with photogrammetry ON (with either 100 or 200 LOD setting) - when either the 10M or 20M version is installed?

standard Bing data is however OK in this locale...

the Swiss Alps look great with this mesh installed.

Edited May 30, 20215 yr by craigeaglefire
...

6 hours ago, craigeaglefire said:

does anyone else have problems with this Swiss Mesh in Zurich City environs with photogrammetry ON (with either 100 or 200 LOD setting) - when either the 10M or 20M version is installed?

standard Bing data is however OK in this locale...

the Swiss Alps look great with this mesh installed.

Are you using the 1.2 version of the mesh?  according to the 1.2 patch notes "* Repaired Zurich Photogrammetry issue"

 

14 hours ago, The Moose said:

Are you using the 1.2 version of the mesh?  according to the 1.2 patch notes "* Repaired Zurich Photogrammetry issue"

no 1.2 patch available for SimMarket version i can find,

also with FSDT Live Update Swiss Mesh does not have Zurich City photogrammetry now,

where did you get the 1.2 patch?

Took the CRJ for a flight from Geneva to Samedan with 20m mesh in VR and I have to say it was a rather disappointing experience. Whole mountains popped into shape some 20 kilometers away. On my first flight (Cessna 152, 10m mesh, VR) I was amazed by the little morphing. On my second one (same aircraft, pancake) I noticed quite a bit of terrain morphing/popping. Now with the CRJ at fl230 it was beyond bearable. I know three flights under different conditions isn’t enough to come to any conclusion but I‘m wondering does anybody get decent results over the Alps with airliners and 20m mesh in VR?

Edited May 31, 20215 yr by Shack95

It probably is all about balance : high FPS with medium settings or lower FPS with higher settings.

We can’t have LOD at 200 and all slides at High/Ultra and throw in Addons like detailed mesh or large AI packages and expect it all being fluid and without morphing....

And perhaps Asobo took some performance of the mesh to devide between other settings.

That was the same with P3D. Updating to DX12 gave extra overhead on high end systems but then again people put their sliders more to the right and ended up with the same performance as before. I was one of them.....

Edited May 31, 20215 yr by GSalden

Yeah, I guess you‘re right. I just can‘t remember having had this issue in X-Plane with HDmesh and zoom level 18-19 ortho. Anyway, let‘s hope MS/Asobo can do something about it in the not too distant future.

9 hours ago, craigeaglefire said:

also with FSDT Live Update Swiss Mesh does not have Zurich City photogrammetry now,

We still haven't released any patch for this, we are working at it right now, should be out later today, most likely,

10 hours ago, craigeaglefire said:

no 1.2 patch available for SimMarket version i can find,

also with FSDT Live Update Swiss Mesh does not have Zurich City photogrammetry now,

where did you get the 1.2 patch?

Apologies...was thinking of the Troglodytus mesh.   Too much mesh available 😄

Edited May 31, 20215 yr by The Moose

We updated our mesh now, with the following improvements:

- Fixed Zurich city photogrammetry

- Fixed an abrupt elevation change at Buochs airport ( LSZC )

 

To get the update, run the FSDT Live Update now.

21 minutes ago, virtuali said:

We updated our mesh now, with the following improvements:

- Fixed Zurich city photogrammetry

- Fixed an abrupt elevation change at Buochs airport ( LSZC )

 

To get the update, run the FSDT Live Update now.

Thanks for the info. Will DL the update.

Umberto, do you happen to know what the real resolution is of France after the France & BeNeLux update ?

Asobo stated that it is as accurate as 5 m but your 10m mesh shows way more detail. Could it be that Asobo is using 5 m data and convert that into 30-50 m mesh ?

Edited May 31, 20215 yr by GSalden

On 5/25/2021 at 2:21 PM, CarlosF said:

I'll stick to default mesh, as adding more and more third party products only increases load times and the chances for CTD. Further down the road, when updates/bug fixes settle, then I will consider alternative products, but not now, I like how this sim looks as it is, quite beautiful if you ask me.

I am with you. The only thing in my community folder is one aircraft.  Too many add ons just invites problems in my opinion. 

I now tried several things including disabling all other addons, yet this strange morphing issue persists. I justed tested the ORBX NZ mesh, I do not see this effects there. I am lost, something must be wrong around Switzerland and Balearics in my case, as I see this phenomenon only in those two regions. Strange...