How do I set the throttles to spool up slowly?

I have the saitek throttle quadrant.

now if I move the throttle to say 25 on the quadrant the a320 shoots straight up to climb thrust.

I would to move them evenly so that if I push the lever to 50 on the quadrant.

it’ll move evenly to 50% n1 Before I push them to toga.

thanks 

mike

35 minutes ago, mikeymike said:

How do I set the throttles to spool up slowly?

I have the saitek throttle quadrant.

now if I move the throttle to say 25 on the quadrant the a320 shoots straight up to climb thrust.

I would to move them evenly so that if I push the lever to 50 on the quadrant.

it’ll move evenly to 50% n1 Before I push them to toga.

thanks 

mike

Try the MSFS(!) sensivity settings. And after that calibrate the thottles via the A32NX EFB

See here:

 

Edited July 14, 20214 yr by Watsi

1 hour ago, Watsi said:

Strange. I'm flying the latest dev and have no problems at all. Maybe try re-calibrating the thottles (EFB)?

So, to tell you the truth, I never calibrated throttles to begin with. I have a Thrustmaster TCA stick in which the throttle lever is used in its full range with no reverse range assigned. I have been flying on default setting since the beginning. I watch the screen annunciator on the PFD to show me the currently selected detent and I verify it visually against the position of the throttle in the virtual cockpit to ensure it's set to the detent it's showing on PFD. I haven't seen a need to do it in a different way up until now. 

1 hour ago, RaptyrOne said:

I am able to log into Navigraph ok. Can access charts etc. I tried again now with a Simbrief flight plan and I can activate that in the CDU and on the Flypad but still no joy with getting charts up. I’ll try again a bit later in case it is a server issue.

I can concur with this. Wednesday 15:30Z

I can load Navigraph charts, normally, out with the Sim

Al

 

33 minutes ago, Watsi said:

Try the MSFS(!) sensivity settings. And after that calibrate the thottles via the A32NX EFB

See here:

 

Thanks for your support. But we do not have the Throttle Settings (Callibration) on EFB (as showvn on the video) ? Apart from the throttles, AP is not able to engage after takeof.

https://ibb.co/ZV6Pffw Please see the picture from tthe dev mode that I have downloaded today via FBW downloader.

I think there is a small discripency, as many other users report the similar issues.

Edited July 14, 20214 yr by kt069

27 minutes ago, Watsi said:

Try the MSFS(!) sensivity settings. And after that calibrate the thottles via the A32NX EFB

See here:

 

Tried al of the a above.

confused as to why i can’t seem to get it right.

Thanks 

mike

4 minutes ago, kt069 said:

Thanks for your support. But we do not have the Throttle Settings (Callibration) on EFB (as showvn on the video) ? Apart from the throttles, AP is not able to engage after takeof.

I think there is a small discripency, as many other users report the similar issues.

Doubled post. Sorry.

Edited July 14, 20214 yr by kt069

9 minutes ago, kt069 said:

Thanks for your support. But we do not have the Throttle Settings (Callibration) on EFB (as showvn on the video) ? Apart from the throttles, AP is not able to engage after takeof.

https://ibb.co/ZV6Pffw Please see the picture from tthe dev mode that I have downloaded today via FBW downloader. Additionally, I did not calibrate the throttles up to now and it was performing with no problem.

I think there is a small discripency, as many other users report the similar issues.

 

1 hour ago, RaptyrOne said:

I am able to log into Navigraph ok. Can access charts etc. I tried again now with a Simbrief flight plan and I can activate that in the CDU and on the Flypad but still no joy with getting charts up. I’ll try again a bit later in case it is a server issue.

 

There was an issue with fbw and navigraph access; they are trying to solve it; It will be up soon.

1 minute ago, hadi said:

There was an issue with fbw and navigraph access; they are trying to solve it; It will be up soon.

Thanks, thought it was just me and I had missed something that needed to be installed separately.

7 hours ago, Watsi said:

Man. I wanted to announce that in half an hour... 😁

Sorry 😅

-double post-

Edited July 14, 20214 yr by Tuskin38

3 hours ago, kt069 said:

Thanks for your support. But we do not have the Throttle Settings (Callibration) on EFB (as showvn on the video) ? Apart from the throttles, AP is not able to engage after takeof.

https://ibb.co/ZV6Pffw Please see the picture from tthe dev mode that I have downloaded today via FBW downloader.

I think there is a small discripency, as many other users report the similar issues.

If you don't have it, you don't have the developer version. This looks like the stable version.

16 minutes ago, Watsi said:

If you don't have it, you don't have the developer version. This looks like the stable version.

I understand your approach but as I have mentioned, I downloaded the developer version today via FBW Downloader. And the new hydraulic features are available, as I can understand it is dev mode. Anyway, as few other collegues reported similar issues, I wanted to report, as wel. I will try to find out. Thanks.

Edit : Sorry, somehow after restarting the sim, by mistake I switched from dev to stable mod. Now cailbration is there. I made the throttle setting and it seems to be ok.

But , it is the first time that I make this calibration to dev FBW (dev). Thanks for the support.

Edited July 14, 20214 yr by kt069

I cant wait to get a new PC as unfortunately my current one is too weak to run any of the airliners. But when I get one I will totally get this amazing A320NEO mod! I can tell the level of work thats going into it is insane and youre well on the way to it becoming MSFS' answer to X-Plane 11s Zibo. Great stuff 😃👍