Selkan

I had the same issue many moons ago running Windows 7 64 bit with FSX. This was on a newly built PC. It turned out that the Bios needed updating. This is far beyond my pay grade and was done for me, but fixed the issues. Just a thought for you guys.

I had this problem a few years ago. I am using PFC Yoke in a home built Sim, FSX and default 737-800. It was eventually found that I had a faulty Potentiometer in the Yoke Unit. At the time PFC provided a replacement and instructions on replacement. The Potentiometer at the time was about ten years old, and like all things do wear eventually. I would suggest this may be the Yoko Yoke playing up. A Potentiometer is normally quite cheap, so if you can find the right replacement is worth a go. At the time I thought it was a calibration issue and played around with the PFC settings/null positions for ages before finding my solution.

Hi, I have posted a similar Post over aerosoft about the following, but thought I would write it here as well. I have My Traffic X installed and all my AI aircraft at Trondheim are a couple of feet under the Apron. I use GSX and that is fine. Also, have Orbx Vector, but ENVA is not listed within their elevation correction tool. I am not sure that would help anyway, as I believe it is My Traffic reading what perhaps is the FSX default height for the airport. I have also had a look within My Traffic folders and within 'Scenery Folder' found one BGL file - ENVA. I have been advised to turn that to 'off' which I did, but did not change anything. If anyone has experience of this particular problem and a possible answer it would be much appreciated. Thanks

Anyone know if this will work in FSX. I have just returned from a holiday in Rhodes, and would love to have this airport.

Don't know if this helps at all, but some years ago I had a similar problem with a new PC (I run FSX by the way). It was found that the Motherboard required updating. The people who built the PC did this, and all was then O.K. This is not an area I would dabble with, but you might like to look into this aspect.

This may or may not help, but it has worked for me in the past and I know it has helped some others. I see you have 16 GB RAM - I assume 8 sticks of 2GB each. Carefully remove them from your PC and switch around; i.e. place No1 stick into slot 8, 2 into slot 7 and so on. Just mix them up basically. I believe it is something called 'creep' when one of the contacts on a RAM strip looses contact. Probably caused by heating up and cooling down. Give it a go, can't do any harm.

Hi Ivar, what can I say; glad to be of service, and hope all 'stays well' Regards, Steven

Hi Ivar, let's hope it has done the trick!

This may have nothing to do with your problem, but recently I started to get freezes in FSX at any time of a flight. Some years ago I experienced a similar problem and found that removing all RAM strips from my PC and then replacing them in a different order did the trick. I have 12 GB RAM in my PC (6 X 2GB strips) I simply put number one in socket 6 and so on. (i.e. in a totally different order/position). I did read in the CTD guide that this can be an issue, and has worked for me. No harm giving it a go!

Hi pete_auau. Well you learn something knew every day! I didn't know GSX now has a follow me car out to active runway, so will be giving this a go later today. Many thanks indeed.

pete_auau. GSX dosn't have a follow me car to take you out to runway, so I find Follow Me very useful at large airports. Also quite often after landing I find the GSX follow me car often seems to have a mind of its own and 'wonders off': the Follow Me car never seems to do this. Although I prefer the GSX car because it takes you to ones gate, the follow me car on arrival just disappears, which of course is not so realistic. But you are right, some sort of conflict going on here. I did try deleting Follow Me and re-installed, but the result was the same.

The FollowMe (2) program is similar to GSX, but allows one to call a follow me car up to go out to active runway as well as calling it to take you to your gate after landing. I am not sure if this program is still available as the originator of the program has stopped all work on it and I believe no longer offers support. If you can find it, it was about £10 to purchase. I used to have version No.1 and that was free, but if you can find version 2 well worth a few quid. Thanks for advice - I think I'm just going to have to use the taxi signs as directed by ATC!!

I have posted this one over on the GSX forum, but so far no joy, so thought I would give it a go here. I have used GSX for a few years now, and have just updated to the latest release 1.9.9 I use a program called Follow Me (2). This is a small program that allows one to call up a follow me car out to the active runway, and back after landing. I use PFC hardware in my homebuilt 737-800 cockpit, and have one of the available buttons on my central consol (throttles etc) mapped to TAB + T and No.1 on release. This is programmed through FSUIPC, and by 'pressing TAB + T brings up the Follow Me menu; by pressing No. 1 on release calls the Follow Me car to my gate or aircraft after landing. Since installing GSX 1.9.9 this call up button no longer works. I also have a key board set into my overhead panel, and again trying to press TAB + T has no effect. I can still bring up the Follow Me Menu by pressing ALT/Addon ons/ and selecting Follow Me/menu - so the program itself is still working. The FollowMe settings menu (outside of FSX) tells me there are no available keys available within FSX to use - which I know to be nonsense! - I have tried changing the key. TAB is standard and can not be changed, but the T could be changed to another letter, but as I say the program says no other key is available. If anyone has a thought on this one it would be much appreciated - frankly I'm foxed!

I don't know if this will help at all. I use PFC rudder set in a home built cockpit. Many many years ago I had a similar problem; well not quite as extreme but similar. Basically I had to go into the PFC settings page (available in FSX by pressing ALT and bringing up the different options) and set up a 'null' centre position for the rudder pedals. This basically meant that any slight movement of the pedals had no effect which means one could taxi in a straight line without any need to touch the pedals. In my case I had to set an extreme left and right position within the settings page as well. I would have thought you will have a settings page for your Logitech Joystick, and you may have to set up similar to the above. This is the only advice I can offer, but hope it might help.

I hope admin. will not mind me posting this here - it is after all the 1st of April 2015. I have just posted a short video called 'Arriving Heathrow' on the Video Library, under the 'Home Cockpit Videos' section. Taken from my 737-800 home built cockpit - landing 27L (day) and 09R (night) - Heathrow London. I think this really has to be as real as it gets!!!!! Enjoy

Name: Arriving Heathrow Category: Home Cockpit Videos Date Added: 01 April 2015 - 09:19 AM Submitter: Selkan Short Description: Landing 27L (day) and 09R (night0 in my home built 737-800 - I think this has to be as real as it gets!! View Video

Julian, this should be the link for you. www.fsdreamteam.com/couatl-live-updates-notes-Couata Live Update Notes Hope that works. If not for any reason just do a search for GSX in google, and find a link to the forums. If the link above does work for you, you will find the link I mention about three updates down from top of page. Sorry try this:- www.fsdreamteam.com/couatl_liveupdate_notes.html just tested and working for me by copying and pasting into your address bar.

Hi Julian2, this may be of help. If you go directly to GSX Update page, there is an update to do with the distance numbers you speak of. On that page is a direct link to the GSX forums speaking about some issues pertaining to FPS drop. That particular problem has been overcome. There are some instructions there for those that do not wish to see the 'numbers' Go to GSX settings (alt tab in FSX first - addons) Go to Simulation page Turn Verbosity tab down one notch. This should remove the distance numbers you don't want to see. I am not using this update myself, as perhaps like you, I don't want to see these numbers, so what I have written above is really just copied over from instructions over at GSX. Hope it works?

Bruce53, your quite right; traffic zapper is part of FSUIPC. Good to use on landing when an AI plane is just about to land in front of you, and you really don't have the time for a go around!

Just a quick question here, which I think I already know the answer to, but thought it worth checking. I downloaded the demo, and had a look at the manual. It says you need an active Internet connection every time you start the application. I have my own 737 800 cockpit, and only connect to the Internet when I want to do an update, or register/activate software etc So, in short, am I correct in saying this software is not for me because I am not connected 100% of the time? Shame, anyway around that?

Excellent. hope that's the fix?

Mac1, will try and help a little further if I can. I have used PM software now for ten years in my home built 737-800. I use PM - MCP/Pilot and Co-Pilot Instrumentation/Eng.Instrumentation/and CDU. Probably some of the following you will already know. Firstly, as mentioned I use PFC Hardware for my FMC which in turn is using the PM CDU software. Within the CDU ini file is a setting that enables me to turn off the actual 'picture' of the FMC, so I only get the text on my FMC Hardware. This is why I can't do a direct test to help you. Having said that, I have over the years had to re-install the CDU program a number of times (change of hardware etc), and have never had the problem you seem to be having. It would make sense that all available buttons on the FMC are useable by default. Are you able to use all other buttons, and is it just the next and previous buttons that do not work? You mention 'settings' above. There are two ways of looking at the settings for all PM software. If you press 'esc' on your key board, this should bring up a menu 'over' your FMC showing different options you can enable or disable. Sometimes for me this has not always worked, so the other way of changing such settings is to go to the 'ini/configuration file. You will find this in the main PM/CDU folder, and is normally placed directly under the CDU exe file. I really can't recall ever having seen such a setting that would turn certain buttons on or off, but to be honest I have never had cause to look for such a thing! If the above does not help, I would suggest you go back to Enrico; he really is your man on this one. Over the years, I have found that he does often think that us mere mortals out here know more than we do, so just ask him for a step by step, and I am sure he will help until the problem is resolved. Sorry that I can't be of more help. Just one last thought; are you running your CDU program on a separate PC and networking to work with FSX? I am, and it is a little complex, but easy when you know how (like most things!)

Hi Mac 1, not sure I can help here, but I use P.M. CDU linked the PFC Hardware. Once I have set up a flight, I can 'step' through the entire flight if I wish using the next page/previous page buttons on the FMC Hardware. I would assume this to be the same on the PM Software. Sorry if this not the answer you are seeking?

Do you have FTX Global installed. This is a requirement for Vector. Over at the OrbX Forums (Vector), you will find a pinned topic on how to uninstall Vector. Sorry can't be more helpful.

Hi Scott, yes, I spotted that and tried, but didn't make any difference for me!