Rusty107

Great find have completed the survey :rolleyes:

Hi Have a look at this thread: http://forum.avsim.net/topic/453694-got-precipitfx-snow-effects-working-in-p3dv2-amazing/ Convinced me to purchase

Hi Ezdok works fine just need to launch from 'outside' of the sim. In my case it wil not load automatically as a module and therefore does not appear as an add-in... Aside from that I would say go for it! I ended up installing a fresh clean 2.4 (after removing 2.3) and everything seems to run well :rolleyes:

I have yet to test however, this may be useful (see post from Beau)!? http://www.prepar3d.com/forum-5/?mingleforumaction=viewtopic&t=7984.0

Hi Being a newcomer to the Linda module and having searched without success, could anyone help me please? I have the Aerosoft Airbus X & the Saitek Multi Panel (the one with the autopilot functions) plus a full registered copy of FSUIPC and the SPAD drivers. I downloaded the lastest AXE Linda profile, however I cannot no matter what I try is get the Autopilot functions to integrate with the Airbus FCU? For example I tried to map the AP1 master to the Linda AP1 script and no joy? Does anyone have a breif how to guide as it would be great to get these two to sync' especially if Aerosopft are close to realeasing the SP Any help/guidance always appreciated! Cheers Rusty

Hi It may be you need to try changing the Graphic Options (not at my Sim PC but try:) Display -> Scenery -> Compexity & Texture Resolution ? Cheers Rusty

Hi This may help? Make sure you read back (after below the line and after the APU BLEED call) "Clear On Two" right after the FO says 'Engine? - Clear on two' Cheers Rusty

Hi Just getting used to the new Q400 and just having a little bit of difficulty as the Below The Line checkilist is not triggered? Here's my flow: 'Before takeoff checklist to the line' Condition Levers? - MAX Trims? 3 SET Flight/Taxi? Flight I then call for 'Below the line' and nothing happens? I have even tried 'before takeoff checklist to the line' still nothing? The green txt at the top show the voice command correctly? Is there a 'trigger' I may have missed? Any help greatly appreciated Cheers Rusty

Hi Have you tried 'replay mode' and seeing if the error is still present?

Yep REX4 and ASN = Extremely convincing weather environment :rolleyes:

Hi I just used the Migrator Tool (IMHO a 'must buy' if you have p3D!) :rolleyes:

Hi I can confirm its a V2 issue as I had no problems with 1.4 - Just have to wait for PMDG...

Hi and many thanks for the replies. OK looks like the performance issue is solely attributed to the SAT being 74C !!! The only fix is to manually edit the weather from the menu as far as I can tell?

Hi everyone Posted in the Majestic Forums too (would love to have a fix if there is one?): Whilst I understand P3D V2 is not fully supported I wonder if anyone else is having a similar issue? It seems to require an incredible lot of runway to accelerate to V1, V2 ! I think this may be down to using AS2012 for my weather (and the very high outside temperatures bug) ultimately I guess the performance of the aircraft would deteriorate based on this? Could anyone confirm if they have this issue and if so any workarounds they may have to allow me to operate the aircraft normally, and not have to use 3000m runways!? Many thanks in advance

Hi If Airbus is your thing then I would highly recommend Aerosoft Airbus X (for P3D) and FS2Crew to go with it Active Sky 2012 is another must have, again this has a native P3D installer, and as mentioned FTX Golbal too!

Great support as always, thank you Bryan :rolleyes: I have edited the ini manually and all seems good, coincidentally I figured it was EZDok causing the sim to hang when it closed, so I have also changed my settings using the Control Panel. Thanks again for all the help Bryan et al. Cheers!

Hi and thank you to everyone for the help, the sim does not shut down properly when using the AXE, never has however, prior to 1.2 the Audio and Crew Region was saved? Is there an ini file I can edit so at least the Audio device and Crew Region is saved? Its no biggie just that I have a couple of extra clicks before I set up a flight :rolleyes:

Hi I am now unable to close the FS2Crew Panel and non of my setting are being saved (HS, Speakers etc) Any idea please anone?

Hi Many thanks to all the help, finally got it working seems thye Legacy mode was the final 'trick' The issue I now face is that when sitting at the gate my FR drop from a decent 15fps to 2fps or 3fps which unfortunately makes the whole thing unusable. I have reduced traffic, ticked only use low res models etc with little improvement? Does anyone have any suggestions as soon as I close FSInn & FSControl Panel my FR go back to normal? I have used SB prior and there is no real FR hit the only problem is online traffic seems to be a bit hit or miss sometimes I see user aircraft other times not? Would love to hear of any solutions as I miss flying online :(

Hi everyone Some awesome repaints out there Not sure if anyone agrees but would be good to see some 'weathered' 'dirtier' 'well used' liveries? Is this quite simple to add for a novice? Cheers Rusty

Hi Many thanks idoleo2001 that seems to have worked, just need to test online (maybe this evening) The only think I am having issues with is that FSinn does seem to recognise my aircraft database. When I try and resync repository there is nothing listed for me to assign as default aircraft? Hope that makes sense and any help gratefully appreciated!

Hi Thanks for the useful links however, when I try and connect to Vatsim I get the 'double tone' indicating connection failed. I would rteally appreciate any help as SB isn't that good in comparison!

Hi Have been running P3D for a couple of months and have a couple of small issues that I hope that you guys could help with please? Whenever I have comms through the headset the speaker sounds seems to reduce quite a lot. Basically the cockpit/engine noise decreases whenever comms are in use even if flying online with Vatsim? Seems to happen if I test with default ATC also? After launching the sim and for quite a while afterwards whenever I click on a desktop icon it seems as though I have clicked twice (with a pause), for example the icons name would appear as though you wanted to rename it? This happens whichever airport or aircraft I am using which means changing EZDOK cameras cannot be used with keyboard shortcuts? I hope the above makes sense(!) and I am using w7P 64bit and run all apps 'as administrator' Any help or advice much appreciated! Cheers Rusty

Hi Greg Quick test last night and all seemed to be ok! Will try abit more testing but I think you have fixed it. Really appreciate the help and I owe you a Long Trail All the best Russ

Hi Installed the new beta and looks like the profiles are still there. I took a backup of the folder prior to installing just in case Hope this helps?