alpha117

Also it is fully compatible with 'SayIntentions' CPDLC/ACARS and also with 'RealACARS'

daft question! So we can now use LINDA for the VRinsight Panel in MSFS 2020? Also is there a MAddog X module, Thanks

have a look here

What we use in the Maddog and have been for the last few years for Printing CPDLC/ACARS is : Replicates the Maddog RW flight deck printer. Cheap on paper rolls also. Cost : approx $35 Thermal Receipt Printer, 58mm Low Noise Plastic Thermal Receipt Printer Stable Performance for Convenience Stores

ACARS/CPDLC Support Released! (sayintentions.ai) 😀

Update will be out by Thursday next week.....slight delay 😉

Get 10% off (sayIntentions.ai ATC) for the first month...valid until the end of the month (Sept) Use this code : MDCPDLC10 Watch the show :

1.Create/Import a flight plan 2. Select the airport in the flight plan 3. Click 'Info' (look down right side) 4. Select runways &gates 5. Select gate from drop down list That's it

Also if you are using Active Sky for weather 122.00 for Closest ATIS position 122.025 for Destination ATIS

looking into this Thanks

Version 2.0.1.6 resolves this issue :smile:

Yes, THE NEXT update will fix the 'no weather'. it has already been tested and works, plus as I said some nice other weather options The next update should be released as soon as Dave has finished some other fixes, hopefully Wednesday evening (USA time) Thank

​This is due to the NOAA URL change. ​Dave has fixed this in the next release along with some nice other weather options :wink:

I would if you are using P2A. There are a LOT of differences in the DATA between the two providers.

It is always a good idea to have the same AIRAC data in P2A and the aircraft that you are using. What AIRAC cycle do you have in P2A. Also P2A can currently only use NavDataPro

If you go to Config > Pilot2ATC Settings there is a checkbox if you want to 'Use SIM Weather(FSX, P3D). Just setup some weather using the SIMs in build weather system and then P2A will use that. DO not check this box if you are using a 3rd party weather engine (AS16, ASN OPUS, REX) Thanks

Is where? If it comes up in the FMC that's good, But if you are using an earlier AIRAC cycle in P2A that would be the problem

Hi What AIRAC cycle are you using in P2A. I've just checked the 1608 cycle and the BDEGA 2 is in there. Also what cycle have you in the 767? Thanks

Hi Steve Not on this one, they will come later

Hi All We have just released this to the BETA team for final testing. Hopefully this should not take to long before being released to the ProATC/X users. We have made lots of changes here a a few of them: 1. Main screen time changed to 24hr clock. Also added 'Select Simulation'. 2. You can now delete more than one flight plan at a time(Shift+cursor down will select the next one.'Cntrl +click' will select only the flight plans clicked) 3. Options > Weather Changed wording to 'Read active Sky Weather' 4. Options > Path to Folders. Added the Aerosoft Airbus(A318-A321) to 'other flight plan paths. 5. Options > Path to Folders. Screen layout changed. You can now select the SIM you are using. Setup the correct path first 6. Options > In Flight. Added 'Automatically save the Flight Situation . The interval in minutes can be changed to suit the current flight. Saved Flights This has been totally re-worked. You MUST delete ALL saved flights that you have BEFORE using the saved flight options. Saved flights will NOT work when: 1.You are on the ground at Departure 2. When you have been asked to contact a controller and have not done so. You will see an in flight message in this case. 3. When you are on approach(allocated rwy). Also if you are using P3D make sure you have 'panel serialization' turn off' (unticked) Alternate Airports 1. These are now imported in ProATC/X if you use a third Party flightplanner (EG PFPX), and use the Flightplan >Import Flightplan > From file. .SFP file format only. If using 'Alternates' then make sure you listen and follow ATC instructions . Requests to return to Departure and Emergencies works as expected. Note: There will only be ONE 'auto' save per flight. You can 'manually save as many as you want also. The current auto save WILL overwrite the previous flights auto save, therefore you will only have ONE auto save Holdings Now given the correct entry procedure(ICAO based holding procedures) Simulation Path (Options> Path to folders) You can now have multiple paths to where you want .pln files to be saved to. Aircraft Data has been 'cleaned' up and now only has fields that are used by ProATC/X SID/STAR/Vectors(Transitions) assigned based on route entry and exit point. SID/STAR transitions: Transitions will automatically be assigned based on route entry/exit waypoints and are expected to be flown. It may be possible to request an alternative transition where necessary. A SID transition will be issued in the ATC clearance. Any STAR transition will be assigned as necessary and listed in the flightplan clearance however you will not be advised by ATC prior to entry. Handover to Approach will be the same as before assigning a STAR. This should work better for the USA. In flight box has been 're-ordered' Taxiways should be fully displayed even where AFCAD entries have zero taxiway width. Last run of 'makerwys' correctly identified with date/time stamp and for all flightsim variants. A lot of 'behind the scenes' coding has been totally re-worked to make ProATC/X a much more realistic ATC experience. Thanks

My only suggestion is to re-install the Duke and confirm that you can select it from within P3D. Then 'ADD' the path to NG. If that still does not work Please create a support zip file (Settings>Create support Package) and e-mail this to Pero Thanks

OK, P3D is slightly different . LM have this. [MAIN] User Objects=Airplane, Helicopter, Submersible, ExternalSim, Avatar Can you select the Duke once P3D has starter, as normal?

Open up fsx.cfg in a plain text editor (I recommend something like Edit Plus or Notepad ++ .) Find the "[Main]" section, it should look something like this: Code: [Main] User Objects=Airplane, Helicopter SimObjectPaths.0=SimObjects\Airplanes SimObjectPaths.1=SimObjects\Rotorcraft SimObjectPaths.2=SimObjects\GroundVehicles SimObjectPaths.3=SimObjects\Boats SimObjectPaths.4=SimObjects\Animals SimObjectPaths.5=SimObjects\Misc

OK, have you added it to your sim.cfg ?

Hi Gregg Goto: Extended settings>SimObjects ConfgSet>Edit Here you can add a 'new SimObject'. Also you can setup various SimObject Config sets, which can be helpful. If you still have any problems then let me know Thanks