July 15, 20178 yr Everytime I fly the NGX I get the master caution light and when I look at failures I have 1, "PAX 02 MASKS DEPLOYED." I set my cruise altitude in the panel and I only had a V/S of 1600 ft. Right above the pressurization it shows a "auto fail" light. My FLT ALT and LAND ALT all have dashes across the display. Anybody else have this problem or have a solution? Josh Scholl
July 15, 20178 yr 4 hours ago, yacoub said: Currently flying to egkk facing same issue with alarm horn Me too. I starting hearing a horn and had no idea until I looked at the cabin altitude. I think it was at 15,000ft, but the packs were on. Sounds like an easy bug to fix unless we're all missing something. George
July 16, 20178 yr Commercial Member For some background... I've made two flights in the NGX in P3DV4 during the past several days, one at FL350 and the other at FL360 and didn't have this issue. I previously had the 747 installed in V3 and V4, then uninstalled everything and rebooted prior to reinstalling the 747-400 and NGX into V4. Best wishes. Dave Hodges System Specs: I9-13900KF, NVIDIA 4070TI, Quest 3, Multiple Displays, Lots of TERRIFIC friends, 3 cats, and a wonderfully stubborn wife.
July 16, 20178 yr dont now if this helps but sounds like a corrupt panel state, when you guys installed the latest version did you by any chance deleted your previous panel save states I7-8700k,Corsair h1101 cooler ,Asus Strix Gaming Intel Z370 S11 motherboard, Corsair 32gb ramDD4,, gtx 1080ti Card, RM850 power supply Peter kelberg
July 16, 20178 yr Just to check, you have set the correct cruise altitude in the pressurisation panel window on the overhead? Cheers, Chris Brand
July 16, 20178 yr 30 minutes ago, PMDG777 said: Just to check, you have set the correct cruise altitude in the pressurisation panel window on the overhead? the op had but dont now about the other 2 I7-8700k,Corsair h1101 cooler ,Asus Strix Gaming Intel Z370 S11 motherboard, Corsair 32gb ramDD4,, gtx 1080ti Card, RM850 power supply Peter kelberg
July 16, 20178 yr Commercial Member Are you using panels states from previous versions ? If yes don't :) create a new one with the current version using as a start situation the default engine running state. Chris Makris PLEASE NOTE PMDG HAS DEPARTED AVSIM You can find us at http://forum.pmdg.com
July 16, 20178 yr 11 hours ago, PMDG777 said: Just to check, you have set the correct cruise altitude in the pressurisation panel window on the overhead? Even if you fail to set the correct altitude the system is smart enough that it will not allow the cabin altitude to go high enough to set off the alarm. Tom Landry
July 16, 20178 yr Commercial Member 34 minutes ago, beep747 said: I have the same issue. Correct altitude set. Jos Denis Again, using old panel states? I.e. From previous version if yes Crete new ones. did you did a full uninstall and reinstall of latest release as per Robert instructions? Chris Makris PLEASE NOTE PMDG HAS DEPARTED AVSIM You can find us at http://forum.pmdg.com
July 16, 20178 yr Yes, I did a full uninstall. I use the short turnaround that came with the new installer. 1 hour ago, Olympic260 said: Again, using old panel states? I.e. From previous version if yes Crete new ones. did you did a full uninstall and reinstall of latest release as per Robert instructions? Jos Denis
July 16, 20178 yr Commercial Member Use the default load, i.e. Engines running, shutdown and save a new panel state and try with that Chris Makris PLEASE NOTE PMDG HAS DEPARTED AVSIM You can find us at http://forum.pmdg.com
July 16, 20178 yr Commercial Member Doors closed? Did you remember to turn the packs back on after start? Kyle Rodgers
Archived
This topic is now archived and is closed to further replies.