Flysimware

Falcon 50 VERSION 1.8C sent to all stores

Recommended Posts

Posted (edited)

Falcon 50 VERSION V1.8A thru V1.8C has the same updated info listed below and on our update page. V1.8C has 2 new updates listed.

 

VERSION 1.8C UPDATES: 3 / 13 / 2019
New Features
  • New payload manager layout with new features that lets you customize payload with more precise range.
  • New visual Fuel truck for changing fuel payloads with sounds. Fuel truck requires engines off and parking brake on.
  • New gear sound with wind, new wind sound, new wheel whine sound and flaps handle sound.
  • Tires are increased in polys to make the roundness smoother.
  • New seatbelt textures and some other various placards in the cabin area.
  • GROUND SUPPORT EQUIPMENT added to user manual table of contents. See page 43.
Bugs & Updates
  • Flight dynamics updated. N2 accuracy is increased. More throttle lever range for higher rpm to help maintain speed.
  • Improved glareshield lighting.
  • Tooltip for the vertical speed hold fixed for fsx.
  • The Hobart sound fixed.
  • Both HSI ADF/VOR needle updated. See the new updated user manual page 10 section 9 for detailed info.
  • The ITT now has a minimum of 15 Celsius displayed for the lowest temp.
  • The APU Generator load now reads between 3 and 5 Amps.
  • Emergency lights now turns off the VC dome light when off or armed.
  • Beacon and strobe lights for P3D updated for flash rate time.
  • Engine gauges updated for accuracy on which bus is powering each unit. See the new updated user manual page 29 section 24 for detailed info.
  • The kohlsman inhg no longer will skip values. It will repeat a value every 12 clicks just as the default tooltip does.
Edited by Flysimware
  • Like 3

Share this post


Link to post
Share on other sites
Help AVSIM continue to serve you!
Please donate today!

Is the latest dynamics file (AIR) already in this build? I tried it with version 1.7B and it is very good.

Share this post


Link to post
Share on other sites
22 minutes ago, Nickbe said:

Is the latest dynamics file (AIR) already in this build? I tried it with version 1.7B and it is very good.

Yes V1.8C has the new airfile.

  • Like 1

Share this post


Link to post
Share on other sites

Just installed v1.8C and have noticed a few things: (using p3d v4.4)

APU sound is way too loud inside the cabin, same volume as in external view.

APU mutes on lost focus with P3D

Strobe lights and Beacon lights are still way too fast.

The Yoke does not work with PBR at night as well as a lot of items in the cabin. Looks like they're glowing (images attached)

Wings also look like they're glowing at night.

Many thanks in advance!!

4Z65OJ9.pngcR6yBei.png

Share this post


Link to post
Share on other sites

Falcon 1.8C, P3Dv4.4, Win10-64

Love it!

Climate control knobs "left drag to adjust" will increase OK, but decreasing falls all the way to 0 (zero).

Share this post


Link to post
Share on other sites
7 hours ago, TomH101 said:

Just installed v1.8C and have noticed a few things: (using p3d v4.4)

APU sound is way too loud inside the cabin, same volume as in external view.

APU mutes on lost focus with P3D

Strobe lights and Beacon lights are still way too fast.

The Yoke does not work with PBR at night as well as a lot of items in the cabin. Looks like they're glowing (images attached)

Wings also look like they're glowing at night.

Many thanks in advance!!

 

I am not seeing the PBR issues you are. Don't know what could be causing that. If no one else reports the same problem perhaps try uninstalling and reinstalling the Falcon.

The beacon flash rate is effected by the Special Effects Setting in P3D under Options\Graphics\World. With the Special Effect Slider set to Medium, I get about 70 flashes/minute, which is right in the middle of the 40 to 100 per minute range required by the regs. With the slider at high I get about 100 flashes/min.

Share this post


Link to post
Share on other sites
Posted (edited)
10 hours ago, TomH101 said:

Just installed v1.8C and have noticed a few things: (using p3d v4.4)

APU sound is way too loud inside the cabin, same volume as in external view.

APU mutes on lost focus with P3D

Strobe lights and Beacon lights are still way too fast.

The Yoke does not work with PBR at night as well as a lot of items in the cabin. Looks like they're glowing (images attached)

Wings also look like they're glowing at night.

Many thanks in advance!!

 

APU sounds come from our custom DLL so sounds will be the same volume for exterior and interior.

No issues with lost APU ever has been reported.

Strobe lights flash rate work based on the special effect slider as explained by AL.

The yokes are bright because you have the overhead map light on. You can tell because the seats are also getting this light. That light should be left off.

The wing out side is something on your end. Like a shader issue from another program. See our pinned post on P3D issues.

Edited by Flysimware

Share this post


Link to post
Share on other sites
Posted (edited)

Thanks for another great update!

Cheers

Martin

Edited by MartinRex007

Share this post


Link to post
Share on other sites

Doesn’t work with P3D4.5 yet

Waiting patiently for the WX Radar update!

xxd09

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now