5 hours ago, ryanbatcund said:

What do you mean doesn't support?  I've got a sidewinder 2 and it's working great.  I had to map controls of course.  

My apologies, Ryan! Although I love my T.16000M, I still have my Sidewinder 2 also. When folks here spoke of the absence of support for long-abandoned (by the respective mfrs.) peripherals, it was my thought that they were referring to immediate recognition by MSFS. Without me doing anything, upon the conclusion of yesterday's installation, MSFS immediately recognized the presence of, and listed, my joystick in the tally of attached peripherals. And, in the controls pull-down, a labeled photo of it is presented.

Once again, my apologies...

20 minutes ago, Flyfaster said:

Can you cut/paste it here?

 

I get the following:

There was a problem logging in to Xbox Live.

Please ensure your account has access to Xbox Live and try again.

Please visit xbox.com

 

THANKS!

Maybe my earlier post in this thread will help?  https://www.avsim.com/forums/topic/580494-ch-pro-yoke-and-pro-pedals-unsupported/?do=findComment&comment=4307117

 

8 minutes ago, Donstim said:

Maybe my earlier post in this thread will help?  https://www.avsim.com/forums/topic/580494-ch-pro-yoke-and-pro-pedals-unsupported/?do=findComment&comment=4307117

 

(For example, I can see that my aileron axis control is a bit jittery and my elevator control does not readily return to center after release)

bingo!

Can't center the thing despite seeing a 'center joystick' option not sure which/what to select for it?  Has anyone tried it or got that option working?

Just a thought as well..... I started with a clean install. That means no more P3D on my system and no addon's (yet) such as FSUIPC. If you have FSUIPC installed and had made controller tweaks in that program, I don't think it is impossible that it may be interfering with the new MSFS. As far as I know FSUIPC is in beta right now for MSFS. I do not have FSUIPC installed and I have set up my CH Products controllers with no effort at all. I do not have twitches, control axis are still when not being touched.

To combat any twitching if present, just set a small (3%-5%) null zone in the Sensitivity setting for the controller. 

Edited August 20, 20205 yr by RaptyrOne

I am relieved to see I am not the only person who has hung onto their CH Products gear. 

1 minute ago, buzzbee said:

I am relieved to see I am not the only person who has hung onto their CH Products gear. 

Well, for some of us it's because it gets the job done and for others it's because other options are just too pricey. Likely even a mix of both in there too. 

I did replace my CH yoke with a Honeycomb Alpha and am so taken with it that I'm planning to replace the quadrant and possible the pedals with the Bravo and Charlie, if they ever come out. I'm oddly sort of glad that FS2020 isn't quite ready yet as it'll make waiting for the Bravo quadrant a bit easier. When I finally sell off the set (or give it away to a family member), I'll definitely feel a bit as if an era has passed. Those products got me through quite a long list of flight products spanning a rather long time.

https://www.youtube.com/watch?v=CxVJXS6NlM0&feature=emb_logo

https://forums.flightsimulator.com/t/ch-products-yoke/124611/86

Edited August 20, 20205 yr by Richard Sennett

To set everything for CH Products manually is a pain.  Hopefully people will share their yoke pedals config files.

Anybody have one that had the basics yoke pedals throttle setup??

 

Thanks 

 

Here's a quick guide to controls for CH Flight Sim Yoke. I don't know if it's the same for Eclipse. My settings were empty at first, I had to select my keyboard config, select all, then switch back to the CH Yoke and they then popped up available to define. I still haven't figured out the sensitivity and dead zones but I hope this helps someone get flying.

 

Flight Control Surfaces

   Primary Flight Control Surfaces

      Aileron Axis - Joystick L Axis X

      Elevator Axis - Joystick L Axis Y

   Secondary Control Surfaces

      Decrease Flaps - 5

      Increase Flaps - 6

      Toggle Landing Gear - 7

Power Management

   Mixture

      Mixture 1 Axis - Joystick R Axis Y   (I had to select reverse axis)

   Throttle

      Throttle Axis - Joystick L Axis Z

 

 

http://vtda.org/docs/computing/CH/800-431_FlightSimYokeUSBQuickStart_Rev1.1.pdf

I did the following steps:

- Install the CH Products Manager (http://www.chproducts.com/13-29170-Downloads-and-Community.php.html)

- Calibrate everything in the CH Products Manager

- Manually map the necessary buttons and axis in MSFS2020.

Works fine (so far). If it helps someone, I can take screenshots. I have the Yoke, Thottle Quadrant and the Rudder Pedals.

3 minutes ago, spakus said:

I did the following steps:

- Install the CH Products Manager (http://www.chproducts.com/13-29170-Downloads-and-Community.php.html)

- Calibrate everything in the CH Products Manager

- Manually map the necessary buttons and axis in MSFS2020.

Works fine (so far). If it helps someone, I can take screenshots. I have the Yoke, Thottle Quadrant and the Rudder Pedals.

Are you finding you need the manager ? thanks 

thanks for the Yoke Settings.
 

I have the Pedals and CH Throttle Quadrant as well

How do you set it up in FS2020 as far as the axis settings?

 

Lots  of choices here..

 

Thanks!

4 minutes ago, spakus said:

I did the following steps:

- Install the CH Products Manager (http://www.chproducts.com/13-29170-Downloads-and-Community.php.html)

- Calibrate everything in the CH Products Manager

- Manually map the necessary buttons and axis in MSFS2020.

Works fine (so far). If it helps someone, I can take screenshots. I have the Yoke, Thottle Quadrant and the Rudder Pedals.

Did exactly this also. Just went in to change toe brakes and now MSFS2020 is not showing either in flight mode 😞 

3 minutes ago, Richard Sennett said:

Are you finding you need the manager ? thanks 

Yes, seems more accurate now with calibrating the stuff in the ch manager.

3 minutes ago, Skyseek said:

´How do you set it up in FS2020 as far as the axis settings?

I've mapped the Throttle 1 and 2 (Axis), Mixture 1 and 2 (Axis), and Prop 1 and 2 (Axis) to the corresponding levers. At the moment I only use one button for the parking brake.