GACSavannah

Look at the pilots lower panel where the electrical switches are located. Top row, center switch is labeled "Electrical Interior". Select that switch to on.

Thank you. I went in and re-activated the Navigraph then tried again and this time they were there.

Perhaps I missed setting something up, but does any one else have any of the airport procedures loaded into the avionics? All I see are visual approaches.

Just did a quick trip around the pattern. IMHO She hand flies really nice, and ground handling is FAR better that the Phenom

There is something not right there Jack. In addition to the glideslope issue you are clearly left of centerline, yet the localizer is showing that you are right of centerline.

when they redid the web site they totally wiped out the home page. Now it only contains two messages and that is it. Totally useless

Yes there is.

Not just you. On my one and only flight I found it to be very squirrely on both the takeoff and the landing rollout. It reminded me of the early versions of the SWS PC-12 the way it wanted to waddle down the runway. I'm sure it will be addressed by the developer if we give him time because he has obviously put a lot of hard work into this.

In case anyone else has the same issues that I had, I was finally able to get the engines running. I went into the Library and did a full download of the plane, so that it was not streaming. I also disabled the few third party liveries that I had installed. After this I was able to get the engines to start. I do not know yet if it was the streamed version of the file, or one of the liveries that was causing the problem, but if you are experiencing the same issue with engines that will not even crank, you may want to try the same actions.

Thank you for the reply, but I have followed the instructions in the manual, the batteries are on, I have selected the engines, one at a time to start. They don't even try to start. Don't even crank. No response at all from either engine.

Thank you. I have tried with fuel pumps on and off, ignitors on, and auto,I even disabled all failures. Still no luck... Still trying...

I am really happy that you all are enjoying it. It has been pure 100% frustration for me. How are you guys even getting this sting started? I have been fighting this dang thing for over three hours and I can not even get the engines started. I even scrapped the dirt with CTL+E. Nothing I do will get the engines running.

I second this. The LOUD videos that can not be stopped are very, very, very annoying. Thank you.

Yes, and they are awful. LOUD volume and often I can not get them to stop playing, so my only choice is to leave the site altogether. Has happened a number of times over the past few days

Thank you!

I have the approach charts in pdf format on a second monitor, and frequently have the area charts on a firefox window signed into skyvector.com. other than that there is nothing else running other that fs2024 (Marketplace edition)

not even using the FMC, other than initializing them. Just doing some quick raw data hand flown aproaches each time.

The only support I could find was on Discord, and I refuse to participate in Discord. Do they have a standard web site for support? Regardless, it has happened across numerous airports. Savannah (KSAV), new Teterboro v2, Hayward CA (KHWD - from the marketplace... many others all in 2024, so it is not tied to any single third party developer.

Sorry, should have included that. It is in 2024.

Has anyone here experienced the NAV radios re-tuning themselves with the FlightFX Citation? For example, you are shooting in ILS and midway through the approach the NAV removes the ILS frequency and re-tunes itself to a nearby VOR. This happens to me frequently. I have poured over the manual and can not find anything about this being an intended feature. Is this simply something on my end or has anyone else seen this ( and if you have can it be disabled?)

I worked for an operator in the late 80s based out of Martin Aviation on the North west side, and regularly flew from the Pilots Co-op. My favorite bird there was a Warrior II, N8251B. I built a ton of hours flying her all over the place. In fact, I still frequently use that N number as my custom registration in FS2024.

You updated to the 2024 version through Orbx Central, or you updated your 2020 version? There was an update for the 2020 version a while back.... I just checked again both Orbx Central and the web site store and neither is showing the 2024 version on my end. Too bad. Would love to pick it up but Justflight doesn't credit my Orbx 2020 purchase and am not going to pay full price when I should be able to take advantage of the discount.

Orbx Central is still not showing it. I wonder if they pulled it with some people having issues with the installer?