I wonder if now they will focus more on the G3000 and it's navigation code?

14 hours ago, Bert Pieke said:

Was offered the upgrade from V9.2.

they didn't offer it to me ☹️, I guess you need to be on SU7 beta 1.21.18.0 then? I am still only on 1.21.17.0

Negative..

25 minutes ago, turbomax said:

they didn't offer it to me ☹️, I guess you need to be on SU7 beta 1.21.18.0 then? I am still only on 1.21.17.0

Go to the content manager

59 minutes ago, Dominique_K said:

Go to the content manager

guess it was sold out last time, this time it did install. thanks!

4 hours ago, Dominique_K said:

But once the MFD is on, the reversionary mode of course goes away. I didn't find a way to switch the MFD back off again in the approach phase to get back the RM. 

from the original manual, don't think this is implemented in MSFS yet:

"Reversionary mode may be manually activated by pressing the Audio Panel’s red DISPLAY BACKUP Button.
Pressing this button again deactivates reversionary mode"

In the event of a display failure, the system can be manually switched to reversionary (backup) mode (all
remaining displays enter reversionary mode). In reversionary mode, all important flight information is presented
on the remaining display(s) in the same format as in normal operating mode.
If a display fails, the appropriate IAU-display Ethernet interface is cut off. Thus, the IAU can no longer
communicate with the remaining display (refer to Figure 1-5), and the NAV and COM functions provided to the
failed display by the IAU are flagged as invalid on the remaining display. The system reverts to backup paths for
the ADAHRS/AHRS, ADC, Engine/Airframe Unit, and Transponder, as required. The change to backup paths
is completely automated for all LRUs and no pilot action is required

Edited December 10, 20214 yr by turbomax

 

 

7 minutes ago, turbomax said:

"Reversionary mode may be manually activated by pressing the Audio Panel’s red DISPLAY BACKUP Button

Not in the Porter at least. I have still to find the red button. There is no vertical bar with the audio panel as shown in the manual. The audio panel comes with the Bendix.

FYI, just posted on the WT Discord site:

"Hello @everyone, we now have the 0.10.1 hotfix available on the Marketplace, which fixes issues with being unable to proceed past bootup on certain aircraft. As always, this is an Early Access Opt-In Beta, so there may be bugs or missing features! Please give us feedback and reports on Discord in our nxi-early-access🥩 channel.

Head to the sim Marketplace to grab the NXi, or go to Content Manager to download the update.

You can find the full (and tiny) release notes here: https://www.workingtitle.aero/packages/nxi/2021/12/10/nxi-release-v0.10.1.html  "

Al

25 minutes ago, Dominique_K said:

I have still to find the red button. There is no vertical bar with the audio panel as shown in the manual.

from the manual you just posted, that everyone praises, and no one reads, according to captain Mark Twain:

 

The G1000NXi red Display Backup button is clickable and animates in the DA-62 and Bonanza G36 Turbo, but unfortunately nothing happens with the PFD or MFD displays when you toggle it.   🙁  I haven't checked any other aircraft.

Al

Edited December 10, 20214 yr by ark

Amazing work !!!!! 

Thank you
Stefano

Looking forward to updating this! Also hoping they spend some time on the G3000/5000 suite. Would be great if we could some new features. I know, this stuff isn't easy and takes time, but it'd be a welcomed update for sure!

2 hours ago, Bdub22 said:

Also hoping they spend some time on the G3000/5000 suite.

It is on their list.. 😉

I went to content manager and installed the latest G1000nxi upgrade.  Everything is working fine, but it changed everything back to Easy.  I've got to write my settings down.  Looks like their going to keep changing them.

I didn't know they were changed until I was going 209 kph on final into KORD.  Everything just quit working. No throttle. Couldn't turn off the AP so I could pull the nose up. Nothing.  Then all of a sudden It dropped to 88 kts in a second or two, and everything worked again.  Go figure.

Roy

Edited December 11, 20214 yr by Roy Warren
mistake in typing

1 hour ago, Roy Warren said:

I went to content manager and installed the latest G1000nxi upgrade.  Everything is working fine, but it changed everything back to Easy.  I've got to write my settings down.  Looks like their going to keep changing them.

I didn't know they were changed until I was going 209 kph on final into KORD.  Everything just quit working. No throttle. Couldn't turn off the AP so I could pull the nose up. Nothing.  Then all of a sudden It dropped to 88 kts in a second or two, and everything worked again.  Go figure.

Roy

It's a bug introduced in sim update 7.  Every time you access the content manager, your accessibility settings get reverted to "easy".