1 hour ago, Axis3600 said:

Ah! Because the same thing I uninstalled all the possible planes by default of asobo, so that's why?

Yes, seems so and as @Bobsk8 has confirmed.

Edited April 15, 20233 yr by Vel

The new models look great.

It has also reinstated the god awful heat haze effect from the engine exhausts, and I cannot get rid of it on the PMDG despite having renamed the heat haze file..

I havent seen much GA action despite having VFR traffic enabled

Edited April 15, 20233 yr by Langeveldt

I'm having some issues with the new injector, 1.4.  Both the current and development versions.  (IFR Traffic 30, VFR traffic 30, delete radius minimum (25km?)

I am getting plenty of departures but no arrivals at all. Tested at EGLL and EGCC.  Both with STARs on and off.

Is anyone else seeing this?  I know my traffic is fairly low, but I like my frames, and am getting plenty of departures. On the log it says the arrival is 25km out, and then "Enroute parked by sim as close to destination"

Edited April 17, 20233 yr by Langeveldt

On 4/16/2023 at 12:04 AM, Langeveldt said:

and I cannot get rid of it on the PMDG despite having renamed the heat haze file..

That's pretty easy. Go into the 'aircraft.cfg' of the PMDG 737. Look for a section called '[EFFECTS]'

In there you find three lines for the heat blur

effect.0 =fx_exhaust_left#(A:GENERAL ENG COMBUSTION:1, boolean)#FX_ASOBO_HEAT_BIG
effect.1 =fx_exhaust_right#(A:GENERAL ENG COMBUSTION:2, boolean)#FX_ASOBO_HEAT_BIG
effect.2 =fx_exhaust_apu#(L:switch_35_73X, number) 250 >#FX_ASOBO_HEAT_BIG

0 and 1 is for the engines, 2 is for the APU. Just comment the lines out. It should look like this

;effect.0 =fx_exhaust_left#(A:GENERAL ENG COMBUSTION:1, boolean)#FX_ASOBO_HEAT_BIG
;effect.1 =fx_exhaust_right#(A:GENERAL ENG COMBUSTION:2, boolean)#FX_ASOBO_HEAT_BIG
;effect.2 =fx_exhaust_apu#(L:switch_35_73X, number) 250 >#FX_ASOBO_HEAT_BIG

Done.

2 hours ago, Watsi said:

That's pretty easy. Go into the 'aircraft.cfg' of the PMDG 737. Look for a section called '[EFFECTS]'

In there you find three lines for the heat blur

effect.0 =fx_exhaust_left#(A:GENERAL ENG COMBUSTION:1, boolean)#FX_ASOBO_HEAT_BIG
effect.1 =fx_exhaust_right#(A:GENERAL ENG COMBUSTION:2, boolean)#FX_ASOBO_HEAT_BIG
effect.2 =fx_exhaust_apu#(L:switch_35_73X, number) 250 >#FX_ASOBO_HEAT_BIG

0 and 1 is for the engines, 2 is for the APU. Just comment the lines out. It should look like this

;effect.0 =fx_exhaust_left#(A:GENERAL ENG COMBUSTION:1, boolean)#FX_ASOBO_HEAT_BIG
;effect.1 =fx_exhaust_right#(A:GENERAL ENG COMBUSTION:2, boolean)#FX_ASOBO_HEAT_BIG
;effect.2 =fx_exhaust_apu#(L:switch_35_73X, number) 250 >#FX_ASOBO_HEAT_BIG

Done.

Thank you!

Can you also fix my problem of no planes landing 😉 

Just one quick question. Are the Asobo models considered generic? I have generic models disabled in the injector's settings. Now that I reinstalled the default aircraft and liveries, wondering if I should enable the generics? Okay, that was two questions.

Edited April 17, 20233 yr by Bones62

I am curious, has anyone seen GA traffic? The few times I have turned it on, I don't think I have spotted any. I have seen some in the injector though.

I have seen some...not very many, but a few each time.

 

same here... but I was flying in remote areas. There were a C172 and a Caravan flying nearby on my last flight

I found out why I'm getting no landings at all, at any airport.  It says "Enroute parked by sim as close to destination", and it does this for every single arrival.  Does anyone have any idea why I'm getting this?

I got a surprise yesterday, flew into PAFA, in the DC 6  and when I taxied , I saw 4 DC 6's parked next to each other. 

I changed the traffic values in the traffic injector and I can't remember the default values, is it a way to return to default values?

I would delete the file

fsltl-trafficinjector-config.json

under

C:\Users\[profile]\AppData\Roaming\fsltl-trafic-injector

A new file with default values should be created upon the next start.

Kind regards, Michael

Edited April 18, 20233 yr by pmb

7 hours ago, Noooch said:

I changed the traffic values in the traffic injector and I can't remember the default values, is it a way to return to default values?

I seem to remember that if you press the FSLTL button inside the sim (the icon on the top bar) it shows the default values.

40 minutes ago, Alvega said:

I seem to remember that if you press the FSLTL button inside the sim (the icon on the top bar) it shows the default values.

It does.