Hello, I have Framerate Generation installed and dssl active. I have an RTX2060 card. I get great Frame Rates for my card, but I get a horrible shimmering/tearing around the aircraft when panning, it is especially bad when taking off, especially around the wheels and nose of the aircraft. Once in the air the double vision/shimmering effect gets less, but still noticable when panning, any ideas?

 

Thank you

 

Paul

I assume this does not happen when you are not using frame generation?

The bottleneck with framegeneration is the VRAM (the RAM of your graphics card). Since there will be additional frames generated, the VRAM of your card (afaik 8GB) gets filled pretty quick. And that is the moment when the stuttering starts. So in higher graphic settings (MSFS)  framegeneration is only a good option for cards with more VRAM (30 or 40 series).

Edited April 13, 20242 yr by Watsi

54 minutes ago, Fielder said:

I assume this does not happen when you are not using frame generation?

Yes! It doesn't happen when frame generation is disabled.

 

Paul

3 hours ago, psouthan said:

Hello, I have Framerate Generation installed and dssl active. I have an RTX2060 card. I get great Frame Rates for my card, but I get a horrible shimmering/tearing around the aircraft when panning, it is especially bad when taking off, especially around the wheels and nose of the aircraft. Once in the air the double vision/shimmering effect gets less, but still noticable when panning, any ideas?

 

Thank you

 

Paul

I had a similar problem a while back and fixed it by using frame limiter with a max frame rate that’s a few frames lower than my max frame limit. 
 

https://forums.flightsimulator.com/t/screen-tearing-in-dx12-with-fg/629730

I also run the mod, and sometimes it helps to switch between DLSS and TAA. Happens in both modes, but switching between them fixes it. Untill it hapens again. Switch, problem solved.

Check your VRAM usage, I assume your 8GB is full loaded, 8GB is not enough to use with FG.

Edited April 13, 20242 yr by Ixoye

37 minutes ago, Ixoye said:

I assume your 8GB is full loaded, 8GB is not enough to use with FG.

It usually is though. In some situations, like badly optimized scenery, it will not be enough. 

The solution is to switch from DLAA to TAA and back. This frees up parts of the VRAM and FG will stop stuttering.

Edited April 13, 20242 yr by Farlis

8 hours ago, psouthan said:

Hello, I have Framerate Generation installed and dssl active. I have an RTX2060 card. I get great Frame Rates for my card, but I get a horrible shimmering/tearing around the aircraft when panning, it is especially bad when taking off, especially around the wheels and nose of the aircraft. Once in the air the double vision/shimmering effect gets less, but still noticable when panning, any ideas?

 

Thank you

 

Paul

This "might" be worth a try. I have a 3060 12 Gig on a second generation Ryzen 7. Try the MSFS 2020 Map mod, it now has 2 cache's DATA and Photogrammetry. I get 70 fps which is smooth as silk. Another tip if you are using Reshade with FG remove it, I gained over 20 fps. P.S. Don't forget to empty the cache's after every flight. Here is an example:

 

Edited April 13, 20242 yr by SierraHotel

5 hours ago, Watsi said:

 So in higher graphic settings (MSFS)  framegeneration is only a good option for cards with more VRAM (30 or 40 series).

 

1 hour ago, Ixoye said:

Check your VRAM usage, I assume your 8GB is full loaded, 8GB is not enough to use with FG.

Respectfully disagree. 

RTX2070 and i3930k 😃

 

Nice video.
Could you try that in a high fidelity airliner (glass cockpit) and inibuilds Heathrow, traffic and heavy weather pls. 😉

26 minutes ago, Watsi said:

Nice video.
Could you try that in a high fidelity airliner (glass cockpit) and inibuilds Heathrow, traffic and heavy weather pls. 😉

I could but that would only tell me what I already know; I have an old and relatively weak system. 
Still doesn’t prevent me having great results with FG.

Edit; into Heathrow with high fidelity airliner, weather, a.i. traffic, with the same system but without FG. I'm going to take a wild guess here but would imagine I'm going to get the same results but with a higher frame rate with FG on?

 

 

Edited April 13, 20242 yr by DD_Arthur

3 hours ago, SierraHotel said:

This "might" be worth a try. I have a 3060 12 Gig on a second generation Ryzen 7. Try the MSFS 2020 Map mod, it now has 2 cache's DATA and Photogrammetry. I get 70 fps which is smooth as silk. Another tip if you are using Reshade with FG remove it, I gained over 20 fps. P.S. Don't forget to empty the cache's after every flight. Here is an example:

 

Correct me if I'm wrong but I did not see any panning in this video. Just switching between preset views.
I too tried FG on my system but as per the OP got game breaking stutters and pauses when trying to pan around using the coolie hat switch on my stick. I thought that it was, possibly, something in my computer/MSFS setup that was not paying nice with the FG mod so decided to revert to my usual TAA selection and also started using the AutoFPS app that seems to work extremely well. I have rarely seen my fps drop below 45 and the whole experience is seamless.

4 hours ago, SierraHotel said:

Try the MSFS 2020 Map mod, it now has 2 cache's DATA and Photogrammetry.

I get terrible stutters when I use the cache with the mod, but totally smooth when I don't.  I have the mods cache on an SSD.

11 hours ago, psouthan said:

Yes! It doesn't happen when frame generation is disabled.

Paul. Have you tried using the AutoFPS utility with FG?  It reacts to a target framerate and automatically adjusts TLOL and OLOD in increments to compensate.  The combination with the FG mode is providing incredibly smooth results for me and I have General Options in MSFS literally max's out.  Would take a very short time to test.  AutoFPS, upon install, has a very good configuration out of the box.  I'd recommend trying it.  You simply install it and run it.  No MSFS or nvidia tweaks required.

One note.  You can run AutoFPS on top as you fly, where you can monitor it.  If you do so, make sure you click on your running MSFS underneath to make sure Windows reccognizes MSFS as its active window.  Otherwise FG is disabled until you do.

Edited April 13, 20242 yr by fppilot