March 9, 20242 yr Just now, Cpt_Piett said: Why oh why can I hear the GSX ground operation sounds whenever I am? Because they are not playing in the sim, but in COATL.
March 9, 20242 yr 7 minutes ago, Cpt_Piett said: I'm having some trouble / getting confused re: the GSX integration. Usually it works, but right now I just loaded aircraft (EFB=>GSX). I was spending some time on Avsim during the process, then when I returned to the aircraft, I found that all PAX and fuel were loaded, but no cargo. So, looking at the aircraft I can see that the cargo trucks (or whatever they're called) are in position, but the cargo doors are closed! And now they can't be opened from the EFB. Actually they open a tiny bit, but not fully - like they're being obstructed by the cargo trucks. See image below. Anyone else seen this? Also, should I set "auto door simulation" and "auto jetway simulation" in EFB-settings-controls when using GSX? It does make sense to do so, but like I mentioned initially - I'm confused... youtube is your friend, i hear you iam still trying to get my head around it ROG Crossair Hero X670e , 9900X, TUF 4090 , X4 NVME's. OS 2TB 980 Pro , MSFS 2TB WD Black , Kington Fury 64GB ram ( 6000) Corsair RM1000 PSU, Artic Freezer iii 360 AIO . Phanteks P600s Case ,TCL QM8B 50" 120 Hz TV,second 24 inch screen for charts you tube etc, and 11" touch screen for the EFB. Warthog Stick and TCA Captains throttle ( full pack) Velocity 1 Rudder Pedals , extreme3D for the Tiller,Streamdeck XL x2 / Streamdeck +/Streamdeck mini because i like pressing buttons
March 9, 20242 yr 1 hour ago, Cpt_Piett said: So, looking at the aircraft I can see that the cargo trucks (or whatever they're called) are in position, but the cargo doors are closed! And now they can't be opened from the EFB. Actually they open a tiny bit, but not fully I might have been a bit quick to blame GSX... Even without it active, the cargo doors won't open. Only a tiny bit, like I mentioned above. So - time to check Fenix knowledge base and Discord EDIT: I'm so stupid - I had yet to connect to ground power... 😝 Edited March 9, 20242 yr by Cpt_Piett 7950X3D | RTX 4090 | 64GB DDR5
March 9, 20242 yr There's lots of little things that they have programmed in there to keep the user from making stupid mistakes. Another example is the logic behing when the GSX integration will actually start the push back. The APU needs to be running. If it isn't you can switch on the beacon until you are blue in the face, nothing will happen. Obvious reason: They will disconnect groundpower while preparing the pushback. If they do that and the APU is off, you are in for nasty surprise. So in order to avoid that from happening, they made the GSX integration dependant on the status of the APU. Genius if you ask me. Edited March 9, 20242 yr by Farlis
March 10, 20242 yr On 3/3/2024 at 2:38 PM, ffantasy67 said: Hi Gents, Anyone having this "server error" on EFB, Mass & balance =>loading aircraft (imported Simbrief flight), only working in "instant" (no server error)? Solving? Thanks, Hi Gents, Solved the above error following a tip on Fenix Discord chat: EFB doesn't like zero "freight cargo" coming from VAs imported flight on Simbrief. Editing some cargo Kg in Simbrief solves the error message returned by the EFB when loading aircraft. Cheers, Massimo Burti Intel Core i9-13900K ¦ 64GB DDR4-3200 - 2x 32GB - Kingston Fury Beast - black ¦ 2x 2TB - m.2 NVMe Gen4 - Samsung 980 Pro ¦ Asus ROG Strix Z690-A Gaming WiFi D4 ¦ Asus TUF RTX 3080 Gaming OC LHR - 12GB ¦ 1000W - 80+ Platinum - Seasonic Prime PX
March 10, 20242 yr 11 hours ago, Farlis said: There's lots of little things that they have programmed in there to keep the user from making stupid mistakes. Another example is the logic behing when the GSX integration will actually start the push back. The APU needs to be running. If it isn't you can switch on the beacon until you are blue in the face, nothing will happen. Obvious reason: They will disconnect groundpower while preparing the pushback. If they do that and the APU is off, you are in for nasty surprise. So in order to avoid that from happening, they made the GSX integration dependant on the status of the APU. Genius if you ask me. So you cant actually simulate INOP APU scenario 🙂 MSFS2020, 24, Fenix A320, Ryzen 9 9950X3D, ASUS TUF RTX 5090 ,G.SKILL 64GB 6000MHz CL28
March 10, 20242 yr 4 minutes ago, roi1862 said: So you cant actually simulate INOP APU scenario 🙂 Well you can, but without GSX. And that's GSX' fault, because they don't allow engine starts on the stand by default. Same problem with any other aircraft. EDIT: And yes I know, you can change this in the aircraft customisation on GSX, but I'd rather now mess with those. Edited March 10, 20242 yr by Fiorentoni For transparency: I'm a community mentor at the BATC discord. However, I do not get paid for it in any way.
March 10, 20242 yr Ok so I got hit by the "spawn at the gate gear up" bug, at EPWA, then tried at another airfield, same. Restarted MSFS, problem gone. 5800X3D, 64GB 3200 RAM, 7900 XT 20GB
March 10, 20242 yr Asobo needs to get in contact with the Fenix team, find out all of the SDK limitations that forced them to use external solutons for the engine modeling then do what needs to be done to update the SDK so that all of that can be done natively. 5800X3D. 32 GB RAM. 1TB SATA SSD. 3TB HDD. RX 9070XT.
March 10, 20242 yr 17 hours ago, Farlis said: There's lots of little things that they have programmed in there to keep the user from making stupid mistakes. Another example is the logic behing when the GSX integration will actually start the push back. The APU needs to be running. If it isn't you can switch on the beacon until you are blue in the face, nothing will happen. Obvious reason: They will disconnect groundpower while preparing the pushback. If they do that and the APU is off, you are in for nasty surprise. So in order to avoid that from happening, they made the GSX integration dependant on the status of the APU. Genius if you ask me. I have to agree with you Farlis, it's quite clever. Just experienced this today: park brake on, beacon lights on BUT APU not started (didn't forget it, wanted to test what you mentioned). As soon as it was available, GSX started pushback. Still need to remember to set APU bleed though! 7950X3D | RTX 4090 | 64GB DDR5
March 10, 20242 yr Il y a 6 heures, Fiorentoni a dit : Eh bien, vous pouvez, mais sans GSX. Et c'est la faute de GSX, car ils n'autorisent pas par défaut les démarrages du moteur sur le stand. Même problème avec n'importe quel autre avion. EDIT : Et oui, je sais, vous pouvez changer cela dans la personnalisation de l'avion sur GSX, mais je préfère maintenant jouer avec ceux-ci. Hello, This surprises me. I am connected to GSX, I remove the Jetway without pushback. Then in MCDU > MCDU MENU > MAINT > GROUND SERVICE I put ON Ground Power + Ground Air (ASU). I start engine No. 2 (without APU - NB: special procedure.) . I withdraw Ground Power + Ground Air (ASU) I ask GSX for pushback, it asks me nose to the right or left. I validate a choice and the pushback is done without problem. Edited March 10, 20242 yr by Area Config : AMD Ryzen 7 9800X3D - MSI PRO B850-S WIFI6E - RAM G.Skill 2 x 32 Go DDR5 6000 MHz CL30 - MSI GeForce RTX 5080 16G VENTUS 3X OC PLUS - 2 WQHD (2560x1440) screens and only one of which is for MSFS
March 10, 20242 yr Commercial Member 7 minutes ago, Bobsk8 said: autopilot disconnecting is starting to be annoying Some tips that are worth trying to: https://kb.fenixsim.com/autopilot-issues
March 10, 20242 yr Just now, polosim said: Some tips that are worth trying to: https://kb.fenixsim.com/autopilot-issues Yeah, I did some of that, going to wait for them to fix it., hope that isn't too many months away,
Archived
This topic is now archived and is closed to further replies.