Search the Community
Showing results for tags 'default'.
Found 28 results
-
I have an issue with the default A321 cockpit. Whenever I download an Airbus addon which already has the default a321 cockpit installed, the 'roll bar' of the flight director never works. The 'pitch bar' always works fine but the roll bar is never active in any mode. Anybody know of any fixes for this?
-
Hi! A couple of months ago when i was about to take a flight with the C337 from Carenado i noticed that my FPS dropped dramatically if i looked down in the VC, and it only happened if i was taxiing over some crossing taxilines. It also happens if i am on the runway with a addon scenery as ground texture. The problem with taxiways occurs in addon sceneries and in default. What i have tried Rebuilt fsx.cfg Checked that FSX is running as admin Taken the settings down Restored default REX config Disabled ENB Series Used a default scenery.cfg New driver from Nvidia. Rolled back after that. Using 267.60. That's the one that followed with my Gainward GTX570 "Goes like hell" Could a possibility have been to restore a default terrain.cfg? I am running NickN's 8xSQ Nvidia Inspector settings. My computer should be able to run that. Any inputs? Here is an example of a taxiway crossing http://www.blade-edge.com/misc/taxi%20pathing.jpg Where the two lines meet, my FPS would have been at 15.
-
i hope this isnt the wrong part of the forum to post this. I am having a weird problem when i add or remove weights in the different payload stations in any aircraft in fsx. If i change a value, it automatically goes back to the default weight values and stations after about a second. However, i can still add and remove fuel. Does anyone else have this problem? I trried removing Abacus carrier task force, as i thought it might have something to do with it for some reason, turns out it had no effect. Any ideas?
-
HiWondering if someone can help me with the open-able doors on this aircraft and where they get their textures. Its not off the fuselage main texture and I have had no luck tracking it down.ThanksJohn
-
Sorry if a topic already exists like this, I couldn't locate one.... What I'm looking to do is restore EVERY file to do with textures.....after GEX, FTX Global, REX, UTX tests I am not 100% sure I executed the uninstall process properly on each addon..... I think i have congested my FSX and Im loosing FPS.....I would like to restore all original texture files properly and install my selected addons based on my tests CLEAN.... Will the repair function actually do this...sometimes I hear yes sometime I hear no...I kind of scared to do it...Am i jeopardizing anything? -
Hi guys, I have a strange problem in saving keyboard/button control in FSX setting menu. Using EZCA I want to delete all default assigned keys/button in FSX, so I enter in settings, controls and erase manually, one by one, all assigned keystrokes. Then click ok and all seems to works fine. When I restar fsx all keystrokes are already there, seems FSX doens't save anything. Any ideas? i am administrator of my system and have full control on files, and my FSX is installed on a separte ssd. By the way....is the a way to delete all assigned keystrokes editing a file? i don't know which is this file that contain keystrokes. Many thanks for your help. -
FOlks, I managed to install VASFMC etc etc etc blah blah blah. I wanted it into my Project Airbus A319 which uses the defualt 321 panel, I WANT THIS. I DO NOT WANT THE VASFMC PANEL! So, i go into my cockpit, and boom, the MCDU is loaded as a pop up. But its not turned on. How do i turn it on? its just a black screen... I try turning the power off and on again, but nothing, just blanked out, no text etc. Any help would be fantastic! Thanks! -Andy
-
Hallo, I fly the default FSXSE CRJ700 a lot. The VC is decent but the texures are not high rez enough for me. So I'd like to fire up GIMP and tweak them to make em sharp and HD. I want to do to the CRJ what the OzX team did to the default Goose (they did a HD Goose Redux). However I cant seem to locate the VC texures files. Im looking for the instrument panel, the cockpit windscreen pillars, the circuit breaker boards etc. The panel folder only has the BMP files for the 2D panel. Im guessing the VC and its textures are in the Bombardier_CRJ_700\model Bombardier_CRJ_700_Interior.mdl Am I right? What program do I need to access the VC? How do I open a .mdl? Is there free software that can do it? Finally, has someone already done this? Created a HD version of the default CRJ VC? I dont want to reinvent the wheel. I've searched extensively and the only ones Ive come across are tweaks to the external model but none for the VC. Just thought Id ask in case Ive missed it! Cheers :) -
I reinstalled the whole simulator an it got even worse. I tried flying on default scenery and nothing is loading, Not that they take long to load, no they even don't want to load. My sliders are on max and my settings on the AMD Control Center are all on default. I haven't touched my my fsx.CFG file yet. It's not the first time I have reinstalled fsx but this is the first time that this happens..
-
Hello, I noticed something weird when I fly through any location I Fly through. It seems like there are default textures between the ORBX textures: I know this shouldn't happen since FTX Replaces the default Textures.... This cant be normal because I have this Problem only since I repaired P3D with the P3D Repair function. https://imgur.com/a/VkFYd5R https://imgur.com/a/nmooSf8 Regards, David
-
I tried searching for this; no luck. I heard there was a way to substitute files so the static carriers have working arresting gear and catupults. If it is possible; could someone give a detailed description of how to make the switch? Thanx in advance Donald
-
Hi all, Recently I started having an issue where some buildings in my default scenery are showing up completely black and others are not showing up except for the roof. It's not a deal breaker but it is extremely annoying when I am on final approach to Miami or DC or any number of other cities and I see these big black cubes or no building but a floating roof. Ultimately I intend to transition over to V4 as soon as I build my new computer this fall but in the interim I would like to fix what I currently have going on. Any suggestions, files, ideas? Much appreciated. Be well Ryan Spel
-
Hello! I've got a pretty annoying problem in p3d v3.. With blurries it seems like im the only one who really has this kind of problems with them. Here is a picture with everything maxed out in p3d: https://gyazo.com/ebdc688e216fd626232f607b06d96a2f it don't really make a difference in the distant blurries if I put all the settings to the right, but I just don't understand why this only happens to me. Yes I know that there is distant blurries in P3D, but I don't think there is on this level. Thanks PC Specs: i5 6500 3.2 - 3.6 GHz GTX 960 4GB OC 8gb 2133 MHz ram Hope that pretty much describes it all. btw I've think I've tried most of the tweaks out there and even tried Nvidia Inspector and reinstalled many times. Thanks. Morten
-
Hi when I load the pmdg ngx 737-800 in P3D it loads in a status where it is about to take off. When init is completed auto throttle is engaged and the plane start rolling. MCP panel settings are not the default. However in PMDG setup i specified Default NGX as the startup panel state. If I immediately pause the game and go into the FMC setup menu and I load the NGX Default state from there, I do get the normal state (with auto throttle off etc) Press execute and it loads normally This is however the startup state in my FMC setup, so it should do this right from the start: I have also saved this "normal" state as user defined state "jacques" and specified this to be the startup state, but this doesn't work either, when loading the plane, it still comes in the "autostart to be engaged" mode. (but again manually loading this state after startup does work) It looks like the panel state is ok by itself (because when I manually load it it is ok) But it looks like this state is not the state loaded during startup, I have nu clue on what state is loaded during startup. What can I do to have P3D start with the "NGX default panel state" ??? Regards Jacques Schenk
-
Just converted to Prepar3D v3 and I have to kick myself for not doing it sooner! Has/will cost me some $$$ but well worth it. Nonetheless, the only real problem I'm having in Prepar3D is the sound(s). The noise from other planes on the tarmac AND in the air is so loud that becomes difficult to hear the ATC. I tried to adjust the "sound" settings in the Settings menu but they control every sound other than the issue I'm having. No issues with cockpit/interior sounds and ATC volume is fine. By process of elimination I thought the environmental slider would reduce external sound affects but it doesn't affect this issue. Added Traffic 360 and starting to think that has something to to with it. If so, I'm not sure how to adjust volume there - is there a way? Again, it's just the external jet engine sound that is distracting. Only happens at the gate (as other planes fire their engines) and on the runways as planes take off and land. Today, while flying into New York City area there was a military helo far enough away that I didn't get a proximity warning but I could hear the chopper engines as we passed as fit i were on it... Strange... Has anyone heard of this problem? Is there a fix?
-
I reinstalled the whole simulator an it got even worse. I tried flying on default scenery and nothing is loading, Not that they take long to load, no they even don't want to load. My sliders are on max and my settings on the AMD Control Center are all on default. I haven't touched my my fsx.CFG file yet. It's not the first time I have reinstalled fsx but this is the first time that this happens..
-
Sometimes, It is hard for me to spot the little yellow default sim aircraft on the moving maps. especially over fall colored terrain. Is it possible for the user to select the color( like Navy blue as an example) for his aircraft? OR change the size to slightly bigger so that it stands out more? Are default aircraft color and size, user selectable in options? Best Regards Hari -
Hello everyone, I am seeking some advice as I am unable to fix this issue myself. Some months ago before I relocated I destroyed my FS setup by installing the FSLABS Control Center and running an update on the FSL Library. Ultimately I removed all add ons and did a complete reinstallation of P3D by following the guide on the P3D forum. However, with a brand new installation of P3D I am getting no more than 8 fps with the default scenario. Here's what I tried already after reviewing several forums with similar issues: - run the P3D Repair Utility - update the GPU Driver - delete certain .cfg files and Shaders - remove unused devices and drivers - reinstall audio drivers - unplug audio devices - change the P3D graphic settings - change some properties in the NVIDIA Control Center I reviewed these threads: [RESOLVED] P3D stuck at very low FPS. - Page 2 - Prepar3D Forums Sudden Drop in Performance - P3Dv4.5 - The Prepar3d Forum - The AVSIM Community Prepar3D v5.3 Bad Performance - Prepar3D Forums Unstable P3D V5.2, Low FPS - Page 2 - Prepar3D Forums Low CPU/GPU Use, Low FPS - Prepar3D Forums None of these solutions had any positive effect. I know my system is not the best, however before I messed up my sim I was able to use FSLABS and PDMG, ORBX and other addons with no issues. Now I'm stuck with 8 fps with no addons even installed. NVIDIA GTX 970, Intel(R) Core(TM) i5-7600K, 16 GB RAM Thanks for helping out!
-
Hey guys, I'm really busy trying to get the PT Tu-154B2 to work, and to get the automatic stabilizer to work, I have to be able to calculate the CG% of the aircraft from the default FSX Fuel & Payload menu. Does anybody know how to do this (may sound a little dumb or silly)? Rafael. -
Hi Folks, So, last night i decided to make my operations in the NGX a lil More realistic, instead of doing the defualt thing when i programme my route on the FMC, and just putting Direct (Airport) i decided to actully plan a flight with a good website which plans it for you ETC, and got all the waypoints The route was EGGP-EGSS (via the waypoints) anyway, there i was, flying along, and i reached my first waypoint, NANTI(if my memory serves right), all very well, but then ATC directs me Further East, meaning i hit the parralels to the other waypoints, but not actully "hit" them, and as for the STARS, they were just not being followed, i was very dissapointed with this, and so i was doing some research this morning on the forums, and people were having the same probs,and reccomendations were that of IVAO and VATSIM, or payware products. I want neither IDEALLY, and would rather freeware, now, the people who had the same specs as me were answered with these,declined them, and then the topic went silent, no products mentioned, so... Is there freeware that can route you through waypoints and SIDS/STARS or not? and if there is, a link would be appriciated, but furthermore, do any of the Virtual Captains from the NGX, or even PMDG workers reccomend what is best, even if the answer is Payware or online ATC Thanks Guys Andy PLEASE NOTE,reasons why i do not want some of the options available I do not want the Payware option becasue as of this second, i cannot justify the price IF there is freeware available I do not want the Online option becuase i do not have the space or "Privacy" to be talkin away whenever feels right etc Thanks For your Understanding
-
I'm getting a lot more serious about flight simulation lately, and since I've always been using vanilla FSX, I think I'd like an upgrade. The C172 is the main choice for me, but I know that most FSX's default aircraft aren't the best. Is the default C172 fine (especially in the flight dynamics), or would an add-on prove quite better?
-
Hi!I have problem with MS ATC at EGLL in FSX Deluxe + Acceleration + Just Flight: Traffic X. When I try to land or take-off from Heatrow, I'm told by default ATC to start/land on runways 09R or 09L. I've tried to set wind both from ~270 or ~90 degrees. I also try change in ADE 1.50 runway properties => primary (09) land/t-off no/no, change primary from 09 to 27, set orphan ILS for 09 runways. And nothing help. I've tried this on UK2000 Heatrow, Ray Smith's EGLL from Avsim and even on borrowed Heathrow from Mega Airports. And I've constant get 09 runways set, although I would like to use set of 27's (commonly used in real life). If anybody had solution or any sugestion is hugely welcome to share this one with me. :)
-
The default Warsaw (EPWA) ground textures for the gates and parking are grass. how can i fix this? https://www.dropbox.com/home?preview=2017-12-26_20-20-33-391.jpg
-
Anyone can how to integrate the gtn750 into the Laminar Baron 3d cockpit? Im interested, thank you.
-
hi, i would like to know if there is a way to start always in the default mode (engines running, ready to take off) and not in dark and cold mode. maybe an .ini or .cfg file? or maybe automatically from the cdu? thank you
